Mechanical engineering topic list of research papers
-
Entropy Generation at Natural Convection in an Inclined Rectangular Cavity2011 / Mounir Bouabid, Mourad Magherbi, Nejib Hidouri, Ammar Ben Brahim
-
Vehicle Detection Based on Perspective Transformation Using Rear-View Camera2011 / Shiho Tanaka, Kenichi Yamada, Toshio Ito, Takenao Ohkawa
-
Heat transfer during condensation of refrigerants in tubular minichannels2013 / Tadeusz Bohdal, Henryk Charun, Małgorzata Sikora
-
Improvement of the Compression-ignition Engine Indicators Using Dual Fuel (Diesel and Liquefied Petroleum Gas)
Abstract The influence of additional supplies of liquefied petroleum gas (LPG) blends is investigated on the energetic and environmental indicators of the compression-ignition (CI) engine operating diesel (dual fuel). By performance of the tests and ...
2016 / Alfredas Rimkus, Modestas Berioza, Mindaugas Melaika, Romualdas Juknelevičius, Zenonas Bogdanovičius -
Dynamic analysis of rotating flexible disk subjected to double slider loading systems
Abstract Rotating disk subjected to stationary slider loading system is a very common mechanical structure. This paper investigates the multibody dynamics of a rotating flexible annular thin disk subjected to double slider loading systems. Along the ...
2012 / Yongchen Pei, Xin Yang -
Point Stabilization for an Underactuated AUV in the Presence of Ocean Currents2015 / Zaopeng Dong, Lei Wan, Yueming Li, Tao Liu, Jiayuan Zhuang, et al.
-
Running Characteristics of Aerodynamic Bearing with Self-Lifting Capability at Low Rotational Speed2011 / Tadeusz Adam Stolarski
-
Direct Sensor Orientation of a Land-Based Mobile Mapping System2011 / Jiann-Yeou Rau, Ayman F. Habib, Ana P. Kersting, Kai-Wei Chiang, Ki-In Bang, et al.
-
Prediction of airborne radiated noise from lightly loaded lubricated meshing gear teeth
Abstract This paper introduces a novel analytical method for determination of gear airborne noise under lightly loaded conditions, often promoting gear rattle of loose unengaged gear pairs. The system examined comprises a single gear pair, modelled...
2015 / S. Theodossiades, M. De la Cruz, H. Rahnejat -
Analysis of cross-ply laminated plates using isogeometric analysis and unified formulation2014 / S. Natarajan, A.J.M. Ferreira, Hung Nguyen-Xuan
-
CNC Paths Optimization in Laser Texturing of Free Form Surfaces
Abstract Laser Texturing and Laser Engraving of free form surfaces are interesting alternative to EDM and micro milling in the fabrication of moulds and dies. The material removal rate of this process is typically very low and the maximum working...
2015 / L. Orazi, F. Montanari, G. Campana, L. Tomesani, G. Cuccolini -
Influence of injection timing and compression ratio on performance, emission and combustion characteristics of Annona methyl ester operated diesel engine
Abstract This study targets at finding the effects of the engine design parameters viz. compression ratio (CR) and fuel injection timing (IT) jointly on the performance with regard to specific fuel consumption (SFC), brake thermal efficiency (BTHE)...
2015 / Ramalingam Senthil, Rajendran Silambarasan, Nattan Ravichandiran -
Nonlinear Free Vibrations of C-C-SS-SS Symmetrically Laminated Carbon Fiber Reinforced Plastic (CFRP) Rectangular Composite Plates2015 / Zakaria Zergoune, Bilal Harras, Rhali Benamar
-
Study the Ways to Forecast the Discharge of Restaurant Wastewater in Beijing
Abstract Combining with empirical method, sector classification, locations of catering industry and comprehensive method, it curve fits and calculates the discharge of Beijing restaurant wastewater from 2004 to 2007 by four fitting formula,...
2012 / Li Ying, Yin Li-Kun, Zhou Jing -
Multi-body Motion Modeling and Simulation for Tilt Rotor Aircraft
Abstract The previous study on modeling of the tilt rotor aircraft used to put a premium on the complicated aerodynamic computation, and the research on the motion equations is often constrained to frequently use the oversimplified 6-degree of...
2010 / Li Haixu, Qu Xiangju, Wang Weijun -
Investigation of Vortex Interaction in Canard-FSW Configurations Based on the Numerical Wind Tunnel Method
Abstract The vortex interference mechanism on low Reynolds number between the canard and main wing of the canard-forward sweep wing (Canard-FSW) configurations is simulated numerically by employing the numerical wind tunnel method. The variations of ...
2010 / Zhang Guoqing, Yang Shuxing, Xu Yong -
Numerical Investigation of the Unsteady Flow in a Transonic Compressor with Curved Rotors
Abstract The unsteady 3D flow fields in a single-stage transonic compressor under designed conditions are simulated numerically to investigate the effects of the curved rotors on the stage performance and the aerodynamic interaction between the...
2008 / Mao Mingming, Song Yanping, Wang Zhongqi -
A linear model of elasto-plastic and adhesive contact deformation2014 / Massih Pasha, Selasi Dogbe, Colin Hare, Ali Hassanpour, Mojtaba Ghadiri
-
A modification of local path marginal cost on the dynamic traffic network2014 / Zheng-feng Huang, Gang Ren, Li-li Lu, Yang Cheng
-
Study and Application of Typical Disaster Monitoring and Early Warning System in Metal Mine
Abstract The typical disaster monitoring and early warning system in metal mine is composed of three parts: production safety awareness platform, cloud platform, integrated management and control platform. Under the metal mining environment, use the ...
2012 / Miaomiao Niu, Shunbing Zhu, Chunquan Du, Nianliang Yang, Wei Xu