Mechanical engineering topic list of research papers
-
Fracture characteristics of refractory composites containing metakaolin and ceramic fibers2015 / O. Hol apek, P. Reiterman, P. Konvalinka
-
Sign Language Recognition with the Kinect Sensor Based on Conditional Random Fields2014 / Hee-Deok Yang
-
Analyzing multiday route choice behavior of commuters using GPS data2016 / W. Tang, L. Cheng
-
A three-stage assembly flow shop scheduling problem with blocking and sequence-dependent set up times2012 / Aref Maleki-Darounkolaei, Mahmoud Modiri, Reza Tavakkoli-Moghaddam, Iman Seyyedi
-
Elastic strain energy density decomposition in failure of ductile materials under combined torsion-tension2014 / Nikos P Andrianopoulos, Vasileios M Manolopoulos
-
An Automotive Engine Charge-Air Intake Conditioner System: Analysis of Fuel Economy Benefits in a Gasoline Engine Application2006 / D W Taitt, C P Garner, E Swain, D Blundell, R J Pearson, et al.
-
A Kind of Real-time Speed Measuring System of High Speed Train Based on Ethernet
Abstract In order to realize speed monitoring of high speed train, we built a kind of monitoring instrument of speed that adopted digital signal processor (DSP) TMS2407, net chip Rabbit3000 and corresponding signal modulation circuits. This...
2012 / Wang Qingmin, Su Mubiao, Liu Yuhong, Yang Yaoen -
Noise Pollution in the re-use of the Electric Vehicles
Abstract With the rapid development of industrial development, the city's noise pollution has become increasingly serious. Based on the principle of re-used energy, analysis of the re-use of noise pollution, and its use in the electric vehicle were. ...
2011 / Ye Shuanggui, Du Chenchen, Zhang Qi -
Formation of X-120 M Line Pipe through J-C-O-E Technique2011 / Jai Dev Chandel, Nand Lal Singh
-
Effect of CH4–Air Ratios on Gas Explosion Flame Microstructure and Propagation Behaviors2012 / Xianfeng Chen, Yin Zhang, Ying Zhang
-
Design and Strength check of Large Blow Molding Machine Rack
Abstract Design procedure of large blow moulding machine rack is discussed in the article. A strength checking method is presented. Finite element analysis is conducted in the design procedure by ANSYS software. The actual situation of the rack load ...
2011 / GU Fei-fei, ZHU Zhi-song, YAN Xiao-zhao, ZHU Yi-min -
A thermal simulation model for laser-assisted milling
Abstract Laser-assisted milling represents an innovative method to realize rough machining of hard-to-machine materials with less tool wear or an increased material removal rate. This paper describes experiments and simulations of locally heating...
2010 / M.F. Zaeh, R. Wiedenmann, R. Daub -
Study of Direct Compression Heat Pump Energy-saving Technology
Abstract Analyzed the feasibility and necessity of the application of heat pump distillation in the gas separation unit. Through the comparison of the results of different heat exchanger, this paper verified the advantages of the heat exchanger with ...
2012 / Wang Ping, Xie Changfang, Xu Shiming, Ge Yulin -
An Experimental Study on the Dynamic Behavior of Grinding Wheels in High Efficiency Deep Grinding
Abstract The design and material of the grinding wheel hub determine its static and dynamic behaviors which, in turn, play significant roles in grinding performance. This can be of special interest in high efficiency deep grinding (HEDG) process, in ...
2012 / Taghi Tawakoli, Holger Reinecke, Alireza Vesali -
Prediction of Milling Cutting Force Coefficients for Aluminum 6082-T4
Abstract Cutting forces modeling is the basis to understand the cutting process, to simulate it and, most important of all, to optimize the process parameters in order to obtain a high quality product with the minimum machining time. In order to...
2012 / G. Campatelli, A. Scippa -
Numerical Simulation of Naval Ship's Roll Damping Based on CFD
Abstract Roll damping test is used to calculate roll damping coefficient, which is an important coefficient in predicting ship seakeeping capability. And because of the complexity of naval ship's shape (with bulbous bow and transom stern), it's rare ...
2012 / Boa Yang, Zuo-chao Wang, Ming Wu -
Vibrations in the Machining System of the Vertical Machining Center
Abstract The paper discusses the equipment and method for measuring vibrations in the tool-workpiece system during face milling. The experimental results show that the vibrations in the tool-workpiece system are dependent on the feed rate. The...
2012 / Edward Miko, Łukasz Nowakowski -
Utilization of integrated CAD/CAE computational fluid dynamic tools in the golf driver design process
Abstract Many factors contribute to the ultimate performance of a golf driver, making evident the need for efficient, accurate, and integrated tools that enable the designer to evaluate various performance trade-offs. Among these design factors is...
2012 / Erik Henrikson, Paul Wood, Keith Hanna -
Aerodynamic study of Human Powered Vehicles
Abstract The key areas with interest of Human Powered Vehicles (HPVs) are the significance of aerodynamic design and ways to improve overall aerodynamics. Wind tunnel testing was undertaken at the RMIT wind tunnel with a selection of both faired and ...
2012 / Firoz Alam, Pedro Silva, Gary Zimmer -
Control strategy of a novel energy recovery system for parallel hybrid hydraulic excavator2015 / W. Li, B. Wu, B. Cao