Mechanical engineering topic list of research papers
-
Hierarchical Control Strategy for Active Hydropneumatic Suspension Vehicles Based on Genetic Algorithms2015 / J. Feng, C. Matthews, S. Zheng, F. Yu, D. Gao
-
Investigation of Boring Bar Dynamics for Chatter Suppression
Abstract Chatter is a concern in boring process, due to the low dynamic stiffness of long cantilever boring bars. Chatter suppression in machining permits higher productivity and better surface finishes. In order to improve the performance of boring ...
2015 / Y. Alammari, M. Sanati, T. Freiheit, S.S. Park -
The ESPA (Enhanced Structural Path Analysis) method: a solution to an implementation challenge for dynamic life cycle assessment studies2014 / Didier Beloin-Saint-Pierre, Reinout Heijungs, Isabelle Blanc
-
Obtaining vehicle parameters from bridge dynamic response: a combined semi-analytical and particle filtering approach2014 / R. Lalthlamuana, S. Talukdar
-
Modeling of the Through-the-Thickness Electric Potentials of a Piezoelectric Bimorph Using the Spectral Element Method2014 / Xingjian Dong, Zhike Peng, Hongxing Hua, Guang Meng
-
Measurement of Gas-Liquid Two-Phase Flow in Micro-Pipes by a Capacitance Sensor2014 / Haifeng Ji, Huajun Li, Zhiyao Huang, Baoliang Wang, Haiqing Li
-
Improving Quality of Wind Tunnel Test Data Through the MDOE
Abstract Researching on the improvement of the wind tunnel data quality through Modern Design Of Experiments (MDOE) was carried out. A body with fin model was tested in wind tunnel through the MDOE and traditional OFAT (One Factor at A Time)...
2015 / Zhang Jiang, Ma Handong, Qin Yongming -
Numerical Simulation and Optimization of Directional Solidification Process of Single Crystal Superalloy Casting2014 / Hang Zhang, Qingyan Xu, Baicheng Liu
-
CFD based Investigation on Internal Cooling of Twist Drills
Abstract To investigate the influence of cutting fluid flow rate and cooling channel exit position on tool wear when drilling with internally cooled cemented carbide twist drills, a model for CFD (computational fluid dynamics) simulations was used....
2014 / F. Fallenstein, J.C. Aurich -
Analytical and Numerical Investigation on the Duffing Oscilator Subjected to a Polyharmonic Force Excitation2015 / Svetlin Stoyanov
-
Fast cooling in dispersively and dissipatively coupled optomechanics2015 / Tian Chen, Xiang-Bin Wang
-
Monocular Vision-based Two-stage Iterative Algorithm for Relative Position and Attitude Estimation of Docking Spacecraft
Abstract Visual sensors are used to measure the relative state of the chaser spacecraft to the target spacecraft during close range rendezvous phases. This article proposes a two-stage iterative algorithm based on an inverse projection ray approach...
2010 / Zhang Shijie, Liu Fenghua, Cao Xibin, He Liang -
Analysis and Flexible Structural Modeling for Oscillating Wing Utilizing Aeroelasticity
Abstract Making use of modal characteristics of the natural vibration of flexible structure to design the oscillating wing aircraft is proposed. A series of equations concerning the oscillating wing of flexible structures are derived. The kinetic...
2008 / Shao Ke, Wu Zhigang, Yang Chao -
Cutting Path Planning for Ruled Surface Impellers
Abstract At present, most commercial computer-aided manufacturing (CAM) systems are deficient in efficiency and performances on generating tool path during machining impellers. To solve the problem, this article develops a special software to plan...
2008 / Liang Quan, Wang Yongzhang, Fu Hongya, Han Zhenyu -
Diesel Engine PT Pump Fault Diagnosis based on the Characteristics of its Fuel Pressure
Abstract In order to solve the problem that the diesel engine PT fuel system is unable to field maintain, developed a portable signal acquisition and analysis system for diesel engine PT fuel system. Firstly, the PT pump work Principle was analyzed, ...
2014 / Xin-jun Wang, Yan-ping Cai, Xu-ze Lin -
Nonlinear Vibration Characteristics of Coriolis Mass Flowmeter
Abstract Coriolis mass flowmeter (CMF) is generally regarded as a linear system when the vibration amplitude of the measuring tube is relatively small, but the spectrum of its output signals still show existence of some multiple frequency...
2009 / Dezhi Zheng, Shuai Wang, Shangchun Fan -
Aircraft Modeling and Simulation with Cargo Moving Inside
Abstract Cargo airdrop has long been one of the most important measures to deal with urgent immediate needs, such as providing assists in military operations and sending relief to disaster areas, just to name a few. Because it is carried out during...
2009 / Jie Chen, Zhongke Shi -
Theoretical modeling and analysis of thermal fracture of semi-infinite functionally graded materials with edge cracks2014 / Vera Petrova, Tomasz Sadowski
-
Temperature Influence on Wear Characteristics and Blunting of the Tool in Continuous Wood Cutting Process
Abstract Temperature of the cutting tool is one of the most important factor affecting the tool wear in wood processing, because the basic properties of the material from which a tool is made, such as hardness, toughness and chemical stability,...
2014 / Izet Horman, Ibrahim Busuladžić, Esed Azemović -
Analysis of Vehicle Detection with WSN-Based Ultrasonic Sensors2014 / Youngtae Jo, Inbum Jung