Mechanical engineering topic list of research papers
-
Variation of cutting forces in machining of f.c.c. single crystals2015 / S. Abolfazl Zahedi, Anish Roy, Vadim V. Silberschmidt
-
Hardness Measurement and Evaluation of Thin Film on Material Surface
Abstract A method for hardness measurement and evaluation of thin films on the material surface was proposed. Firstly, it is studied how to obtain the force-indentation response with a finite element method when the indentation is less than 100...
2011 / Lin-dong WANG, Min LI, Tai-hua ZHANG, Nai-gang LIANG -
Variation of Material Parameters for The Thickness Extensional Mode of Piezoceramic Discs in Case of Mechanical Loading
Abstract Here, we report on the variation of material parameters of piezoceramic discs due to applied static and isotropic mechanical loads. Such mechanical loads frequently occur in piezoelectric sensor and actuator devices. In order to achieve...
2012 / Stefan J. Rupitsch, Jürgen Ilg, Alexander Sutor, Reinhard Lerch -
Cascade Hopfield Neural Network Model and Application in Robot Moving Process
Abstract Based on the principle of discrete Hopfield neural network, the paper proposes a cascade Hopfield neural network controller model and applied in a miniature inchworm robot locomotion process. According to the robot moving modes in one...
2012 / Yu Lianzhi, Liang Weichong -
Dynamic Sliding Mode Control Scheme for Electro-Hydraulic Position Servo System
Abstract In order to solve the uncertainties in the position servo system, caused by servo system without modeling accurately, which may cause the deterioration of the control quality of the electro-hydraulic position servo system (EHPSS) and even...
2011 / Rui Tang, Qi Zhang -
Motion Planning of a Snake-Like Robot Using an Optimized Harmonic Potential Field2011 / Samer Charifa, Marwan Bikdash
-
Adaptive control of a synchronous motor via a sliding mode decomposition technique
Abstract This paper presents a decoupled control strategy using time-varying sliding surface-based sliding-mode controller for speed control of permanent magnet synchronous motor (PMSM). The decoupled method provides a simple way to achieve...
2011 / Fayez G. Areed, Sabry F. Saraya, Mohamed M. Abd Elsalam -
Simplified equivalent models of large-scale wind power and their application on small-signal stability2013 / Nan Ding, Zongxiang Lu, Ying Qiao, Yong Min
-
Wind speed equalization-based incoming wind classification by aggregating DFIGs2013 / Zhaojun Meng, Feng Xue, Xueming Li
-
Research on the Dynamic Hysteresis Loop Model of the Residence Times Difference (RTD)-Fluxgate2013 / Yanzhang Wang, Shujun Wu, Zhijian Zhou, Defu Cheng, Na Pang, et al.
-
Four Methods for Roundness Evaluation
Abstract Whether roundness error can be evaluated accurately and efficiently or not will directly influence the mechanical products performance and life. For this reason, this paper introduces simple and efficient algorithms to evaluate the...
2012 / Wentao Sui, Dan Zhang -
Research of Simulation on the Effect of Suspension Damping on Vehicle Ride
Abstract The mathematical model of four degrees of freedom vehicle suspension was established, based on that, built the vibration differential equation and road excitation matrix; the frequency response function and root mean square value which...
2012 / XueMei Sun, Yaxu Chu, Jiuchen Fan, Qiuxiao Yang -
Effect of Variogram Types on Surrogate Model based Optimisation of Aircraft Wing Shapes
Abstract Engineering design problems always require enormous amount of real-time experiments and computational simulations in order to assess and ensure the design objectives of the problems subject to various constraints. In most of the cases, the...
2012 / Raman Balu, Selvakumar Ulaganathan, Nikolaos Asproulis -
Tip-over Prediction for Omnidirectional Mobile Robot
Abstract This paper proposes a holonomic omnidirectional mobile robot with active dual-wheel caster assemblies as a robotic transport vehicle. With concern to the sudden dynamic changes during maneuver, the tip-over stability monitoring is very...
2012 / M. Juhairi Aziz Safar, Keigo Watanabe, Shoichi Maeyama, Isaku Nagai -
Research on Infrared Carbon Monoxide Monitoring System Based on Least Squares Support Vector Machine
Abstract Carbon Monoxide (CO) is a kind of poisonous and explosive gas which does harm to people and safety production. A infrared Carbon Monoxide monitoring system based on Least Squares Support Vector Machine is illustrated. Detected principle of...
2012 / Zhang Li, Dang Nan, Gong YuHan -
Variational Bayesian Two-Stage Kalman Filter for Systems with Unknown Inputs
Abstract In this paper, we consider the probabilistic approach in adaptive state estimation for discrete-time linear stochastic time-varying systems with unknown inputs. When lack knowledge of noise, we regard the system state, unknown inputs and...
2012 / Junlong Sun, Jie Zhou, Xuekui Gu -
A Lateral Control Method of Intelligent Vehicle Based on Fuzzy Neural Network2015 / L. Li, H. Wang, J. Lian, X. Ding, W. Cao
-
Air flow control based on optimal oxygen excess ratio in fuel cells for vehicles2013 / Ai Guo, Weirong Chen, Qi Li, Zhixiang Liu, Haidan Que
-
Research on Embedded CNC Device Based on ARM and FPGA
Abstract This paper proposes a design of embedded numerical control device based on ARM and FPGA through research on CNC architecture and embedded device development program of CNC. This paper researches the transplant process of Linux embedded...
2011 / Jiyou Fei, Ran Deng, Zhao Zhang, Mo Zhou -
Effects of shear stress on the microalgae Chaetoceros muelleri2010 / Michiel H. A. Michels, Atze J. van der Goot, Niels-Henrik Norsker, René H. Wijffels