Mechanical engineering topic list of research papers
-
Change in Surface Magnetic Flux Density in EDM of Permanent Magnets-Influence of Internal Temperature and Shape on Machined Magnets
Abstract Traditional machining of a permanent magnet is difficult because of magnetic forces and brittleness of materials. However, electrical discharge machining (EDM), which is a non-contact thermal machining method, has carried out for shape...
2013 / H. Takezawa, Y. Ichimura, N. Yokote, N. Mohri -
Optimized design on water cooling system of CHMFL
Abstract The effectiveness of the technique of naturally stratified and the dispersible uniformity of the diffuser that is used in the conditions of large flow rate and large temperature difference has been verified. The thermocline in all these...
2013 / J.L. Tang, Z.R. OuYang -
Seismic stability evaluation of embankment slope based on catastrophe theory2013 / Hongwei Zhu, Lingkan Yao, Yuan Luo
-
The Effect of Cutting Parameters on Cutting Force During Turning Multiphase Microalloyed Steel
Abstract The multiphase (ferrite-bainite-martensite) microalloyed steel was turned to study the effect of machining parameters such as cutting speed, feed and depth of cut on cutting forces. The mechanical properties of the multiphase microalloyed...
2012 / V. Sivaraman, S. Sankaran, L. Vijayaraghavan -
To the Question of Validity Grüneisen Solid State Equation2012 / Vladimir Kh. Kozlovskiy
-
Developing an Empirical Relationship to Predict Tensile Strength of Friction Stir Welded AA2219 Aluminum Alloy2008 / K. Elangovan, V. Balasubramanian, S. Babu
-
Fully Developed Forced Convection Heat Transfer in a Porous Channel with Asymmetric Heat Flux Boundary Conditions2011 / Ozgur Cekmer, Moghtada Mobedi, Baris Ozerdem, Ioan Pop
-
Genetic Algorithm for Concurrent Balancing of Mixed-Model Assembly Lines with Original Task Times of Models2013 / Panneerselvam Sivasankaran, Peer Mohamed Shahabudeen
-
Study on the Temperature Changing Rules of U75V Rail in the Cooling Process
Abstract Caused by the differences in volume and heat dissipation area of rail head and bottom, latent heat of phase transition releasing and other reasons, the complicated temperature changes occurs in rail head and bottom between during the...
2011 / Gao Mingxin, Song Hua, Jia Hao, Jiang Juanjuan, Tong Shanhu, et al. -
Rooftop photovoltaic (PV) systems for industrial halls: Achieving economic benefit via lowering energy demand
Abstract Industrial halls are characterized with their relatively high roof-to-floor ratio, which facilitates ready deployment of renewable energy generation, such as photovoltaic (PV) systems, on the rooftop. To promote deployment of renewable...
2012 / Bruno Lee, Marija Trcka, Jan L.M. Hensen -
An intelligent curve warning system for powered two wheel vehicles2010 / Francesco Biral, Mauro Da Lio, Roberto Lot, Roberto Sartori
-
Service Systems Engineering Applications
Abstract The rapid growth in the global service economy has greatly increased research in Service Science and Service Systems Engineering (SSE). In Service Systems practice, the service value chain in terms of links among system entities is defined...
2013 / Amit J. Lopes, Ricardo Pineda -
3D Model-Based Simulation Analysis of Energy Consumption in Hot Air Drying of Corn Kernels2013 / Shiwei Zhang, Ninghua Kong, Yufang Zhu, Zhijun Zhang, Chenghai Xu
-
Basic Study of Combustion-Material Removal Process by Multi-Function Electrode
Abstract Using the characteristic that most metal can burn in oxygen, put forward a new high-efficiency process that deals with the difficult-to-cut materials multi-function electrode EDM-induced ablation machining technology. Design the...
2013 / L. Zhidong, X. An’yang, Q. Mingbo, X. Jun, L. Wenpei -
Vehicle Lateral State Estimation Based on Measured Tyre Forces2009 / Ari J. Tuononen
-
Effect of Thermal Cycle on the Formation of Intermetallic Compounds in Laser Welding of Aluminum-Steel Overlap Joints
Abstract The intermetallic compound (IMC) (or intermetallic phase layer) has a significant influence on the mechanical properties ofjoints between dissimilar metals obtained by thermal processes such as laser welding. Its formation is basically...
2011 / J. Fan, C. Thomy, F. Vollertsen -
In situ drag measurements of sports balls
Abstract Aerodynamic drag on sports balls is typically measured in wind tunnels. There is a concern that fixtures needed to support the ball in a wind tunnel may influence its drag. Measurements under game conditions have been attempted, but are...
2010 / Jeffrey R. Kensrud, Lloyd V. Smith -
Thermal Hydraulic Analysis Using GIS on Application of HTR to Thermal Recovery of Heavy Oil Reservoirs2012 / Yangping Zhou, Fu Li, Zhiwei Zhou, Yuanle Ma
-
Improvement of Pyroelectric Cells for Thermal Energy Harvesting2012 / Chun-Ching Hsiao, An-Shen Siao, Jing-Chih Ciou
-
A Novel Fuzzy-Neural Slack-Diversifying Rule Based on Soft Computing Applications for Job Dispatching in a Wafer Fabrication Factory2013 / Toly Chen, Richard Romanowski