Mechanical engineering topic list of research papers
-
Development and Testing of a Design Protocol for Computer Mediated Multidisciplinary Collaboration during the Concept Stages with Application to the Built Environment
Abstract Effective collaboration and maximum effort from stakeholders during the feasibility and concept design stages in architecture provide the greatest potential for added value for the overall success of a building project, from the initial...
2014 / Marianthi Leon, Richard Laing, Julian Malins, Huda Salman -
H control for path tracking of autonomous underwater vehicle motion2015 / L.-L. Wang, H.-J. Wang, L.-X. Pan
-
Modelling cavitating flow around underwater missiles2015 / Fabien Petitpas, Richard Saurel, Byoung-Kwon Ahn, Sungho Ko
-
Optimization of Microwave-Based Heating of Cellulosic Biomass Using Taguchi Method2013 / Kuo-Hsiung Tseng, Yong-Fong Shiao, Ruey-Fong Chang, Yu-Ting Yeh
-
Comparision of Contact and Contactless Measuring Methods for Form Evaluation
Abstract Coordinate measuring machines (CMM) are mostly used with contact sensors. High accuracy and very good results in repeatability are advantages of contact systems. Sometimes it is necessary to measure parts, which are not suitable for contact ...
2012 / Peter Kaťuch, Miroslav Dovica, Stanislav Slosarč’k, Jozef Kováč -
Numerical analysis of two and three dimensional buoyancy driven water-exit of a circular cylinder2015 / Shahab Moshari, Amir Hossein Nikseresht, Reza Mehryar
-
Investigations of hydraulic operating conditions of air lift pump with three types of air-water mixers2015 / Marek Kalenik
-
Trajectory tracking control of underactuated USV based on modified backstepping approach2015 / Zaopeng Dong, Lei Wan, Yueming Li, Tao Liu, Guocheng Zhang
-
Dynamics Analysis of Close-coupling Multiple Helicopters System
Abstract The particularity and practicality of harmony operations of close-coupling multiple helicopters indicate that the researches on it are urgent and necessary. Using the model that describes two hovering helicopters carrying one heavy load, an ...
2008 / Zhao Zhigang, Lu Tiansheng -
Direct Numerical Simulation of Secondary Breakup of Liquid Drops
Abstract This article studies numerically a familiar important phenomenon in spray combustion which is deformation and breakup of liquid drops in gas flow. The SIMPLER method is used to solve the two-dimensional (2D) unsteady axisymmetric...
2010 / Liu Jing, Xu Xu -
Design and preliminary validation of a tool for the simulation of train braking performance2013 / Luca Pugi, Monica Malvezzi, Susanna Papini, Gregorio Vettori
-
Performance Analysis of a Novel Air-based Cavity Receiver
Abstract In this paper a new design of a novel CSP cavity receiver for parabolic trough collector is analyzed by means of an analytical Matlab model. The receiver, designed by the Swiss company Airlight Energy Manufacturing SA, is 212 m long...
2014 / P. Matarrese, A. Gaetano, S. Airaghi, D. Montorfano, M.C. Barbato, et al. -
Health assessment of gasoline and fuel oxygenate vapors: Generation and characterization of test materials
Abstract In compliance with the Clean Air Act regulations for fuel and fuel additive registration, the petroleum industry, additive manufacturers, and oxygenate manufacturers have conducted comparative toxicology testing on evaporative emissions of...
2014 / Michael Henley, Daniel J. Letinski, John Carr, Mario L. Caro, Wayne Daughtrey, et al. -
Analysis and Integration of Design for X Approaches in Lean Design as basis for a Lifecycle Optimized Product Design
Abstract All product lifecycle processes are highly determined by product design. The concept of Lean Design focuses on maximizing customer value and minimizing waste throughout all stages of product lifecycle by an optimized product design. Design...
2014 / Uwe Dombrowski, Stefan Schmidt, Kai Schmidtchen -
Development of Customer Satisfaction Models for Affective Design Using Rough Set and ANFIS Approaches
Abstract Rough set (RS)- and particle swarm optimization (PSO)- based adaptive neuro-fuzzy inference system (ANFIS) approaches are proposed to generate customer satisfaction models in affective design that address fuzzy and nonlinear relationships...
2013 / Huimin Jiang, C.K. Kwong, M.C. Law, W.H. Ip -
Numerical and Experimental Investigation of Plastic Interaction Between Rough Surfaces2014 / Radosław Jedynak, Marian Sułek
-
Study on Ignition Probability of Flammable Materials after Leakage Accidents
Abstract It is a key step of quantitative risk analysis (QRA) to estimate ignition probability of flammable materials after leakage accidents. This paper reviews the available literature and expert opinion on how to evaluate and determine ignition...
2012 / Changlong Zhu, Juncheng Jiang, Xiongjun Yuan -
Exergy Analysis of Ultra Super-critical Power Plant
Abstract In this study, exergy analysis was performed for ultra super-critical power plant. The analysis was carried out by means of process simulation using a computer model developed in Microsoft Excel .The model was based on the concepts of coal...
2013 / Sandhya Hasti, Adisorn Aroonwilas, Amornvadee Veawab -
Application of Space-time Conservation Element and Solution Element Method in Intake and Exhaust Flows of High Power Density Diesel Engine
Abstract A one-dimensional pipe flow model of single-cylinder diesel engine is established to investigate the intake and exhaust flow characteristics of diesel engine in the condition of high power density (HPD). A space-time conservation element...
2013 / You Guo-dong, Xu Chun-long, Xu Jun-feng, Zhu Ming, Wang Zeng-quan -
Study on Judgment Method of Combustion Mode on Dual-mode Scramjet
Abstract It was very significant to judge the combustion mode of engine correctly, because the distributions of fuels and other parameters of combustion mode switching depended on it. This paper proposed to a judgment method of combustion mode of...
2014 / Q. Chen, L.H. Chen, H.B. Gu, X.Y. Zhang, P. Wang