Materials engineering topic list of research papers
-
Development of reliability and probabilistic safety assessment program RiskA
Abstract PSA (probabilistic safety assessment) software, the indispensable tool in nuclear safety assessment, has been widely used. An integrated reliability and PSA program named RiskA has been developed by FDS Team. RiskA supplies several standard ...
2015 / Yican Wu -
Reactivity and Microstructure of Al 2 O 3 -Reinforced Magnesium-Matrix Composites2014 / Maher Mounib, Matteo Pavese, Claudio Badini, Williams Lefebvre, Hajo Dieringa
-
Wear Behaviour of Nanocrystalline Fe88Si12 Alloy in Water Environment2014 / Licai Fu, Jun Yang, Qinling Bi, Weimin Liu
-
The PWM speed regulation of DC motor based on intelligent control
Abstract The PWM speed regulation of DC motor based on intelligent control is discussed. The simulation is carried out with the SIMULINK after that the mathematical model of controlled object is built. This article introduces the PWM bipolar drive...
2012 / Wenbin Yan, Dada Wang, Pengfei Jia, Weiguo Li -
New method for signal encryption using blind source separation based on subband decomposition
Abstract A novel cryptosystem based on subband decomposition independent component analysis (SDICA) is proposed in this work, where no assumption of independence for the ciphers and the plaintexts is required. In the proposed cryptosystem, the...
2008 / Zuyuan Yang, Guoxu Zhou, Zongze Wu, Jinlong Zhang -
An Optical Performance Monitoring Model Based on RBFANN Trained with Eye-Diagram
Abstract An optical performance monitoring model based on radial basis functions artificial neural network was proposed in this paper. This proposed model can simultaneously identify three kinds of impairments, namely optical signal-tonoise ratio,...
2012 / Mahua Wang, Shihu Wang -
A low-cost built-in self-test method for resistive MEMS sensors
Abstract This paper illustrates the experimental application of the LIMBO method, an identification method based on binary observations dedicated to the (self-) test of integrated electronic and electromechanical systems, such as MEMS. The tested...
2012 / O. Legendre, H. Bertin, O. Garel, H. Mathias, S. Megherbi, et al. -
Preparation and properties of desulfurization gypsum-slag hydraulic cementitious materials
Abstract Desulfurization gypsum is the desulphurization products of wet FGD process in coal-fired power plants. However, it has not been widely used by far. In order to expand the application scope of desulphurization gypsum, desulphurization...
2012 / Honggen Qin, Xiaoqin Liu, Gang Li -
Transient analysis of LP rotor from NPP 900MW turbine
Abstract Thermal stress and the contact stress for centrifuge force field during the start up and shut down is very most important for the safety of the turbine which will affect the design life of the turbine. The stress at startup and shut down is ...
2012 / Mingxiang Gong, Di Guo, Zhaoxi Wang, Zhenhao Shi, Fei Xue, et al. -
Sputtered thin film piezoelectric aluminium nitride as a functional MEMS material and CMOS compatible process integration
Abstract A comprehensive study on the complete process module for the fabrication of AlN-based MEMS sensors and actuators is presented. The investigations include the influence of the electrode material, AlN thickness and stress tuning during...
2012 / S. Marauska, T. Dankwort, H.J. Quenzer, B. Wagner -
Compressive behaviours of lotus-type porous copper fabricated by Gasar process
Abstract The lotus-type porous copper with various pore structural parameters was fabricated by a novel solid-gas eutectic solidification process (the Gasar process). The effects of porosity and the Angle between load direction and pores axis (ALP)...
2012 / Zaijiu Li, Tianwu Yang, Qinglin Jin, Zhenhua Li, Yehua Jiang, et al. -
Structural and Optical Properties of SiOx Films Deposited by HFCVD
Abstract Room-temperature photoluminescence (PL) of non-stoichiometric silicon oxide (SiOx, x<2) films prepared by hot filament chemical vapour deposition (HFCVD) technique was studied. The effect of the growth temperature was analyzed. These...
2012 / J. A. Luna López, G. García Salgado, A. Ponce Pedraza, D. E. Vázquez Valerdi, J. Carrillo López, et al. -
AMR gradiometer for mine detection and sensing
Abstract We used anisotropic magnetoresistors (AMR's) to build an advanced mine detector. The sensing head involves gradiometric pair of AMR sensors and a continuous-wave driven excitation coil, so the gradiometer is capable of detection...
2012 / Jan Vyhnanek, Michal Janoseka, Pavel Ripka -
Study of Rational Water Injection Parameters of Hydraulic Pressing Preventing Outburst Measure Based on Numerical Simulation
Abstract With the increase of the mining depth in coal mine, the safe producing of mine is seriously restricted by outburst danger of driving working face of coal road. For solving the problem, in this paper, mechanics model is created about...
2011 / Fang Qian-cheng, Li Zhi-qiang, Zhou Ke-ping -
Fuzzy Clustering and Visualization Analysis of Tool Wear Status Recognition
Abstract One of the biggest problems in manufacturing is the failure of machine tools which due to loss of surface material in cutting operations. Therefore, an effective diagnosis mechanism is necessary for the tool condition monitoring so that...
2011 / Pan Fu, Weilin Li, Liang Guo -
Impact Analysis of Climate Change on Water Resources
Abstract It has theoretical and realistic meanings to study the climate change's impacts on hydrology and water resources, so as to understand and solve some problems in hydrology and water resources, such as plan management, operation management,...
2011 / Yang Nan, Men Bao-hui, Lin Chun-kun -
Ultrathin Glass as Flexible Substrate in Wireless Sensor Applications
Abstract Flexible antenna is an essential part for the wireless sensor applications such as aerospace, communications, mobile communications, telemetry, medical, RFID etc., therefore, there is a huge interest in developing such antenna and in...
2012 / D. Feili, N. Pagel, P. Schwarz, H. Seidel -
High Throughput Fabrication Process for Polymer MEMS using Molding and Printed Pattern Transfer
Abstract We propose a new MEMS fabrication method utilizing a mold replication process and a pattern transfer on the screen-printed film. The polymer MEMS device was fabricated in fabrication characteristic with a high-throughput and all vacuum less ...
2012 / K. Kurihara, S. Takamatsua, T. Kobayashi, H. Takagi, R. Maeda -
Preface2012 /
-
Integrating Materials and Manufacturing Innovation: a new forum for the exchange of information to integrate materials, manufacturing, and design engineering innovations2012 / Charles H Ward