Materials engineering topic list of research papers
-
Evaluation on the Post-buckling Residual Strength of H-shaped Steel Column
Abstract As steel columns under unexpected accidental loading exhibit a tendency of plastic deformation in large buckling, the issue has been much discussed along with the evaluation of plastic deformation capacity and restoring force of column...
2011 / Hwon-mo Park, Jae-hyouk Choi -
Research Progress and Comparison of Methods for Testing Self Ignition Materials
Abstract Fires due to spontaneous combustion make up a very small portion of total fires, but they result in great loss and it's hard to conduct a fire cause identification. This paper is mainly about the research progress of self ignition...
2011 / FEI Fan, LIANG Dong -
Fiber-optic interferometric sensor of magnetic field for structural health monitoring
Abstract In this paper we report on results of measurement of AC and DC magnetic field by fiber-optic interferometric sensor. Principle of operation is based on change of length of optical path cavity between the magnetostrictive wire and...
2010 / Z. Djinovic, M. Tomic, C. Gamauf -
High cycle fatigue behaviour of magnesium alloys
Abstract The influence of crystallographic texture on fatigue failure mechanisms was studied by comparing the fatigue behaviour of two extruded magnesium alloys, AZ31 and ZN11. The microstructures and fracture surfaces of specimens were examined...
2010 / L. Nascimento, S. Yi, J. Bohlen, L. Fuskova, D. Letzig, et al. -
Quantitative Characterization of Mechanical Properties using Instrumented Indentation
Abstract Instrumented indentation testing (IIT), an advanced version of conventional hardness tests, is widely used to evaluate the mechanical behavior of materials. Compared to conventional mechanical tests such as tensile testing, saw-cutting,...
2011 / Young-Cheon Kim, Won-Seok Song, Jong-Heon Kim, Kug-Hwan Kim, Dongil Kwon -
Heat treatment of a friction-stir-welded and spin-formed Al-Li alloy
Abstract Prototype end domes for cryogenic propellant tanks were fabricated using friction stir welding and spin forming technology. Subsequent heat treatment of a dome to a high strength temper resulted in weldment properties which were below...
2011 / Stephen J. Hales, Wesley A. Tayon -
Fatigue crack growth in Ti-6242 under elasto-plastic loading conditions
Abstract The applicability of LEFM is investigated in this paper. Experiments with loads corresponding to load controlled LEFM conditions and LCF strain controlled conditions were carried out and the crack propagation was monitored. The experiments...
2010 / Magnus Hörnqvist, Tomas Mänsson -
Engineering Numerical Simulation on the Amount of Make-up Air for Mechanical Smoke Exhaust in Atrium
Abstract Smoke is one of the major hazards on to the occupants in atrium fires. It is commonly accepted that the smoke should be timely exhausted. Make-up air must be supplied simultaneously to the atrium in order to keep the smoke exhausting...
2011 / S.C. Li, Y. Chen, X. Chen, G.G. Jing -
Strain Measurements within Fibre Boards. Part II: Strain Concentrations at the Crack Tip of MDF Specimens Tested by the Wedge Splitting Method2012 / Gerhard Sinn, Ulrich Müller, Johannes Konnerth, Jörn Rathke
-
Exploration of New Electroacupuncture Needle Material2012 / Sanghun Lee, Gwang-Ho Choi, Chang Hoon Lee, Yu Kyoung Kim, Saebhom Lee, et al.
-
Advanced Strategies for Articular Cartilage Defect Repair2013 / Amos Matsiko, Tanya Levingstone, Fergal O'Brien
-
Manufacturing of Nanostructured Rings from Previously ECAE-Processed AA5083 Alloy by Isothermal Forging2013 / C. J. Luis, D. Salcedo, J. León, I. Puertas, J. P. Fuertes, et al.
-
Glass Fiber Reinforced Polypropylene Mechanical Properties Enhancement by Adhesion Improvement2012 / Mariana Etcheverry, Silvia E. Barbosa
-
Noise Smoothing for Structural Vibration Test Signals Using an Improved Wavelet Thresholding Technique2012 / Ting-Hua Yi, Hong-Nan Li, Xiao-Yan Zhao
-
Photocatalytic Materials2012 / Guohua Jiang, Tao Chen, Qiang Yang
-
Validation of the heat and mass transfer models within a pressurized water reactor containment using the International Standard Problem No. 47 data2013 / Tomasz Bury, Jan Składzień, Adam Fic
-
A “Friendly Merger” in the War on Cancer2002 / M Sadelain
-
Coupling between finite element method and material point method for problems with extreme deformation
Abstract As a Lagrangian meshless method, the material point method (MPM) is suitable for dynamic problems with extreme deformation, but its efficiency and accuracy are not as good as that of the finite element method (FEM) for small deformation...
2012 / Yanping Lian, Xiong Zhang, Yan Liu -
Hot nanoindentation in inert environments2010 / Jonathan C. Trenkle, Corinne E. Packard, Christopher A. Schuh
-
Multi-core CPU or GPU-accelerated Multiscale Modeling for Biomolecular Complexes2013 / Tao Liao, Yongjie Zhang, Peter M. Kekenes-Huskey, Yuhui Cheng, Anushka Michailova, et al.