Materials engineering topic list of research papers
-
Influence of fatigue damage on the mechanical behaviour of 2024-T3 aluminum alloy
Abstract The present work is devoted to study the influence of high cycle fatigue damage rate at R = 0.1, on the mechanical properties of aluminum alloy 2024-T3 which is largely used in aircraft industry. The study consists of an experimental...
2011 / A. May, M.A. Belouchrani, A. Manaa, Y. Bouteghrine -
First-principles calculation of structural and electronic properties of Ti-doped B13C2
Abstract Stability and electronic properties of Ti-doped boron carbides (B13C2) were studied using the first principle calculations based on plane wave pseudo-potential theory. The calculated results showed that Ti atom doped in boron carbide was in ...
2011 / L. Yu, S.K. Lu, Y.L Jiang, B. Xiao, X. Tang, et al. -
Eigenstrain modellingof residual stresses generated by arraysof LSP shots
Abstract This paper presents an eigenstrain (misfit strain) model to predict the residual stresses (RS) generated by arrays of laser shock peening (LSP) shots (i.e. adjacent to each other over a surface patch or overlapping layers of LSP shots)where ...
2011 / Mithila Achintha, David Nowell -
Predicting New Materials for Hydrogen Storage Application2009 / Ponniah Vajeeston, Ponniah Ravindran, Helmer Fjellvåg
-
A high-density ternary barcode detection system with a fixed-period delay method
Abstract A fixed-period delay method is proposed to increase the detection range and detection stability of a ternary barcode detection system. The system combines an envelope differential detection technique containing nonlinear filtering and a...
2010 / Hiroo Wakaumi -
Design of Equal Precision Frequency Meter Based on FPGA2012 / Yi-yuan Fang
-
Optimization of Dry Sliding Wear Performance of Ceramic Whisker Filled Epoxy Composites Using Taguchi Approach2012 / M. Sudheer, Ravikantha Prabhu, K. Raju, Thirumaleshwara Bhat
-
Evaluation of an [ 18 F]AlF-NOTA Analog of Exendin-4 for Imaging of GLP-1 Receptor in Insulinoma2013 / Dale O. Kiesewetter, Ning Guo, Jinxia Guo, Haokao Gao, Lei Zhu, et al.
-
A Review of Ionic Liquid Lubricants2013 / Anthony Somers, Patrick Howlett, Douglas MacFarlane, Maria Forsyth
-
An experimental and numerical lifetime assessment of Al 2024 sheet
Abstract This work is concerned with the simulation of ductile damage evolution and the respective final material failure resulting from load reversals (LCF). For that purpose, a continuum damage mechanics (CDM) model proposed by Lemaitre is...
2010 / Shehzad Saleem Khan, Dieter Hellmann, Olaf Kintzel, Jörn Mosler -
A quantum version of the classical Szilard engine2013 / Paul Bracken
-
Improvement in Mechanical Properties of Standard 15CDV6 Steel by Increasing Carbon and Chromium Content and Inoculation with Titanium during ESR2012 / T. R. Bandyopadhyay, P. K. Rao, N. Prabhu
-
Flexural Behavior of Extruded DFRCC Panel and Reinforced Concrete Composite Slab2012 / Chang-Geun Cho, Bang Yeon Lee, Yun Yong Kim, Byung-Chan Han, Seung-Jung Lee
-
Lipoidal Soft Hybrid Biocarriers of Supramolecular Construction for Drug Delivery2012 / Dinesh Kumar, Deepak Sharma, Gurmeet Singh, Mankaran Singh, Mahendra Singh Rathore
-
Effect of Surface Roughness and Materials Composition2012 / Maryam Gharechahi, Horieh Moosavi, Maryam Forghani
-
An Improved Model for FE Modeling and Simulation of Closed Cell Al-Alloy Foams2010 / MD. Anwarul Hasan
-
Application of the QCM in lead acid batteries electrolyte measurements
Abstract This paper describes the application of a Quartz Crystal Microbalance (QCM) sensor in density-viscosity measurements of the electrolyte of the lead acid batteries. In battery applications, especially in automotive applications, submarines...
2010 / A. Cao-Paz, L. Rodríguez-Pardo, J. Fariña -
Dependence of thermal conductivity on structural parameters in porous samples2012 / L. Miettinen, P. Kekäläinen, T. Turpeinen, J. Hyväluoma, J. Merikoski, et al.
-
Homogeneous Thermal Cloak with Constant Conductivity and Tunable Heat Localization2013 / Tiancheng Han, Tao Yuan, Baowen Li, Cheng-Wei Qiu
-
Ultra-High-vacuum Experimental Equipment to Characterize Shape Memory Alloys for Space Applications
Abstract An experimental ultra-high-vacuum facility capable of measuring the deformation during thermal cycles under load at different temperatures has been designed and developed to characterize the shape memory effect in the environmental and...
2015 / I. López-Ferreño, U. Urrutia, P. Lorenzo, M. Collado, C. Rivera, et al.