Materials engineering topic list of research papers
-
Influence of SPS casing treatment on axial flow compressor subjected to radial pressure distortion
Abstract The present work is about the stall margin enhancement ability of a kind of stall precursor-suppressed (SPS) casing treatment when fan/compressor suffers from a radial total pressure inlet distortion. Experimental researches are conducted...
2016 / Fanyu Li, Jun Li, Xu Dong, Dakun Sun, Xiaofeng Sun -
Completion difficulties of HTHP and high-flowrate sour gas wells in the Longwangmiao Fm gas reservoir, Sichuan Basin, and corresponding countermeasures
Abstract For safe and efficient development of the sour gas reservoirs of the Cambrian Longwangmiao Fm in the Anyue Gas Field, the Sichuan Basin, and reduction of safety barrier failures and annulus abnormal pressure which are caused by erosion,...
2016 / Yufei Li, Chaoyi She, Niannian Liu, Huali Zhang, Lin Zhang, et al. -
Electric Vehicle Charging Using Photovoltaic based Microgrid for Remote Islands
Abstract This paper presents a real-time energy management scheme for electric vehicle (EV) charging using photovoltaic (PV) and energy storage, connected to the microgrid. The scheme is based on the heuristic rule-based strategies to optimize...
2016 / Abdul Rauf Bhatti, Zainal Salam, Ratil H. Ashique -
Toroidally symmetric/asymmetric effect on the divertor flux due to neon/nitrogen seeding in LHD
Abstract Toroidal distributions of divertor particle flux during neon (Ne) and nitrogen (N2) seeded discharges were investigated in the Large Helical Device (LHD). By using 14 toroidally distributed divertor probe arrays, which were positioned at...
2016 / H. Tanaka, G. Kawamura, S. Masuzaki, M. Kobayashi, T. Akiyama, et al. -
Dielectric barrier discharge actuator for vehicle drag reduction at highway speeds2016 / Subrata Roy, Pengfei Zhao, Arnob DasGupta, Jignesh Soni
-
Interlayer couplings, Moiré patterns, and 2D electronic superlattices in MoS 2 /WSe 2 hetero-bilayers2017 / Chendong Zhang, Chih-Piao Chuu, Xibiao Ren, Ming-Yang Li, Lain-Jong Li, et al.
-
Restoring Wooden Structural Elements and Transparent Structures: Protection and Rehabilitation of Bosnian-Herzegovinian Medieval Fortifications
Abstract A great number of medieval fortifications in Bosnia-Herzegovina is in a state of deterioration, lacking ceiling and roof structures, usually made of wood. Their components usually make part of other structures in open areas covered with...
2016 / Amir Čaušević, Nerman Rustempašić, Amira Salihbegović -
Constructing Non-linear Shaping Envelops in Current Architecture
Abstract The paper focuses on constructing curvilinear structural envelops in digital avant-garde project of the 21st century. Buildings with non-linear shape force relationships between geometry and material which are different than before. Virtual ...
2016 / Krystyna Januszkiewicz -
Influence of the acceptor roughness on the aspect ratio of silver paste lines printed by laser-induced forward transfer
Abstract Silver paste voxels and lines are printed by laser-induced forward transfer onto three different substrates. Increasing the roughness of the acceptor substrates enhances the aspect ratio of the lines printed.
2016 / Y. Chen, M. Morales, D. Munoz-Martin, C. Molpeceres -
The Improvement in Collection of Municipal Waste on the Example of a Chosen Municipality
Abstract Ecologistics is the concept which in Poland is not commonly known and is defined differently. The new Waste Act which entered into force in 2013, rose interests in logistics aspects which improve municipality management. Despite many...
2016 / Michał Jakubiak -
Self-adaptive Multi-purpose Modular Origami Structure
Abstract A research line in architecture and interior design has been focused for years on the selection of materials with properties specifically tailored for light, thermal and acoustic comforts. An adaptive origami-based structure is here...
2016 / Silvia Andreozzi, Gaia Ilenia Bessone, Matteo Botto Poala, Martina Bovo, Silvia Fernandez De Alaiza Amador, et al. -
Printed Strain Gauges Embedded in Organic Coatings
Abstract In this work we present a method for the fabrication of all-printed strain gauges on pre-coated sheet steel substrates. The state of the art is to glue strain gauges on foil onto a substrate. This, however, has inherent disadvantages in...
2017 / Herbert Enser, Pavel Kulha, Johannes K. Sell, Bernhard Jakoby, Wolfgang Hilber, et al. -
HFO1234ze as Drop-in Replacement for R134a in Domestic Refrigerators: An Environmental Impact Analysis
Abstract In this paper are reported the results of an experimental comparative analysis between R134a and HFO1234ze, when they are employed as refrigerants in a domestic refrigerator. Under sub-tropical conditions, it have been measured the energy...
2016 / Ciro Aprea, Adriana Greco, Angelo Maiorino, Claudia Masselli, Antonio Metallo -
Controllable two-scale network architecture and enhanced mechanical properties of (Ti5Si3+TiBw)/Ti6Al4V composites2016 / Y. Jiao, L. J. Huang, T. B. Duan, S. L. Wei, B. Kaveendran, et al.
-
A VR-based Interactive System to Improve Users’ Involvement in OAP Development
Abstract Open-architecture products (OAPs) allow users to add personalized functional modules in an original product to meet changeable requirements for the product. The development of personalized products requires users’ involvement to meet the...
2016 / Hao Song, Qingjin Peng, Jian Zhang, Peihua Gu -
Effects of growth temperature on the properties of InGaN channel heterostructures grown by pulsed metal organic chemical vapor deposition2015 / Yachao Zhang, Xiaowei Zhou, Shengrui Xu, Zhizhe Wang, Zhibin Chen, et al.
-
Elastic, magnetic and electronic properties of iridium phosphide Ir2P2016 / Pei Wang, Yonggang Wang, Liping Wang, Xinyu Zhang, Xiaohui Yu, et al.
-
The use of Flexible Tubular Elements of the Overhaul and Tunnels Reconstruction
Abstract The normal operation of the tunnels may not always be secured by renovations in current content. In some cases the factors affecting the condition of the tunnel construction (engineering-geological conditions, seismic effects, material and...
2016 / Sergei Kokoshin, Nicholas Ustinov, Boris Kirgincev -
Novel arithmetic operations on type-2 intuitionistic fuzzy and its applications to transportation problem
Abstract Type-2 intuitionistic fuzzy sets possess many advantages over type-1 fuzzy sets because their membership functions are themselves fuzzy, making it possible to model and minimize the effects of uncertainty in type-1 intuitionistic fuzzy...
2016 / Dipak Kumar Jana -
Development, Verification and Validation of 3DFloat; Aero-servo-hydro-elastic Computations of Offshore Structures
Abstract The aero-servo-hydro-elastic Finite-Element-Method code 3DFloat is tailored for nonlinear, coupled time-domain simulations of offshore structures in general and offshore wind turbines in particular. This article describes the theory behind...
2016 / Tor Anders Nygaard, Jacobus De Vaal, Fabio Pierella, Luca Oggiano, Roy Stenbro