Materials engineering topic list of research papers
-
Surface Relief Shaping by Combined Machining of Aluminum Alloys
Abstract The article describes the formation of surface topography in combined finishing machining. Use of combined machining can achieve a better quality of the resulting surface. Multiple studies have helped to formulate the main provisions and...
2016 / V.E. Inozemtsev -
Research and Development of Tubular Products Magnetic Pulse Welding–Forming Technology for Space Engineering
Abstract The analysis of the aircraft onboard cables design made by the authors has shown that it is most expedient to reduce the weight of the bonding of electrical connectors through replacing a molded housing of the plug connector by a...
2016 / S.V. Nescoromniy, E.L. Strizhakov, D.V. Rogozin -
Early age shrinkage pattern of concrete on replacement of fine aggregate with industrial by-product
Abstract This is an experimental work carried out to investigate early age shrinkage pattern of concrete, prepared, on 50% replacement of industrial by-product (like pond ash and granulated blast furnace slag) as fine aggregate using OPC, PPC and...
2016 / R.K. Mishra, R.K. Tripathi, Vikas Dubey -
Examination the Torsion Properties of pin-to-plate LAMP Joint
Abstract Laser assisted metal plastic (LAMP) joining is a promising new joining technology. In the course of this study, not the mostly examined overlapped sheet to sheet, but the pin-to-plate geometry is investigated. This geometry maybe useful for ...
2016 / Tamás Markovits, Andor Bauernhuber, János Takács -
Dynamics of Adhesion Control for Different Lubricants
Abstract The article presents two examples of testing the adhesion properties for the lubricants of two sorts, namely: plastic and liquid in dynamics. Maintaining perfect control of the adhesion characteristics for different lubricants in contact...
2016 / K.N. Voinov -
Series SRR Loaded UHF RFID Tag
Abstract An RFID tag based on a series loaded split ring resonator (SRR) to operate in the European UHF RFID band of 865-867MHz is reported. A chip of impedance 27-j212Ω is connected at the terminals of the antenna and the read range measurements of ...
2016 / K.K. Aju John, Thomaskutty Mathew -
Intellectual Ring Laser Quality Control System – Key Component of Ring Lasers Science-Based Production
Abstract Production of the ring lasers is a science based manufacturing process to apply variety of technologies (mechanical, optical, vacuum, electronic). Nowadays, the manufacturing facilities arrangement which has been established at the initial...
2016 / A.V. Belov, T.I. Soloveva -
Dual–voltage Micro-electricity Grids
Abstract Most developing countries are facing energy shortage and this impacts the social and economic development. Reliable electrical networks are absolutely necessary for energy supply. Unfortunately, the energy access has become a major problem...
2016 / C. Moller, A. Marino, B. Tchanche -
An Approach for the Sensory Integration into the Automated Production of Carbon Fiber Reinforced Plastics
Abstract The advantages of Carbon fiber reinforced composites (CFRC) lead to an increasing demand of Carbon fiber products. This class of materials is gaining widespread acceptance in various fields like aviation, wind energy or automotive and is...
2016 / Johannes Graf, Kristina Gruber, Yi Shen, Gunther Reinhart -
Kinetic Roof Structure: Msheireb Heart of Doha
Abstract Barahat Al Nouq is the central square of the heart of Doha, capital of Qatar. Following traditional Arabic architecture, the new roof construction is reinterpreting ancient building elements which already functioned adaptive and responding. ...
2016 / Gregor Grunwald, Thomas Hermeking, Thomas Prang -
Probabilistic failure analysis for glass components under general loading conditions
Abstract In this work, an experimental programme consisting in four-point bending and coaxial double ring tests is performed on glass specimens with different dimensions. The results are analyzed using a novel probabilistic model aiming at proving...
2016 / Alberto Ramos, Miguel Muniz-Calvente, María Jesús Lamela-Rey, Pelayo Fernández, Alfonso Fernández-Canteli -
Estimation of solar radiation and optimum tilt angles for south-facing surfaces in Humid Subtropical Climatic Region of India
Abstract In the present work, availability of solar radiation for south-facing flat surfaces in Humid Subtropical Climatic Region of India has been estimated. Measurements of global and diffuse solar radiation for Aligarh (27.89°N, 78.08°E) which...
2016 / Basharat Jamil, Abid T. Siddiqui, Naiem Akhtar -
Liquid Sloshing in Fuel Storage Bays of Advanced Reactor Subjected to Earthquake Loading
Abstract Earthquake-induced loads on components and structures related studies are vital to ensure the safety of the plant. In this work, the Fuel Storage Bay (FSB) of typical Indian advanced reactor has been taken for estimating the design...
2016 / M. Eswaran, G.R. Reddy -
Performance Evaluation of a Novel Multi-pass Solar Air Heating Collector
Abstract In this present investigation, the performance of a new solar air heating collector of multi-pass mode is presented. The solar air heating system is theoretically modelled by applying energy balance expressions to reflect the network of...
2016 / M.W. Kareem, Khairul Habib, K. Sopian, Kashif Irshad -
Fatigue of superelastic NiTi wires with different plateau strain
Abstract Microstructures and thermomechanical responses of Ni-rich superelastic wires can be tuned in relatively large extent by varying the degree of cold work and heat treatment. What frequently remains unknown is the superelastic fatigue...
2016 / O. Tyc, J. Pilch, P. Sittner -
Orientation selectivity in a multi-gated organic electrochemical transistor2016 / Paschalis Gkoupidenis, Dimitrios A. Koutsouras, Thomas Lonjaret, Jessamyn A. Fairfield, George G. Malliaras
-
Influence of heat treatment on cyclic fatigue and cutting efficiency of ProTaper Universal F2 instruments
Abstract Background/purpose Heat pretreatment can improve the cyclic fatigue life of nickel–titanium (NiTi) instruments. This study evaluated the effects of two different heat treatments on the cyclic fatigue resistance and cutting ...
2016 / Chih-Wen Chi, Eddie Hsiang-Hua Lai, Chao-Yuan Liu, Chun-Pin Lin, Chow-Shing Shin -
Engineered Hours Per Product for Simultaneous Engineering
Abstract Modern Cooperative Engineering approaches suggest a transparent tracking of production costs during development stages. The traditional concept of Engineered Hours per Product, originally developed for the automotive industry, focusses on...
2016 / Jan-Fabian Meis, Anna Theresa Tüshaus, Gunther Reinhart -
The Road Steel Bridge Over Bosut River in Serbia Part 1: The Assessment of the Bridge
Abstract Maintenance requirements for existing bridges outpace more and more available resources each day. Besides improved repair techniques, this situation emphasizes the need for a comprehensive approach to bridge management. An important...
2016 / Mirjana Malešev, Vlastimir Radonjanin, Đorđe Lađinović, Ivan Lukić, Slobodan Šupić, et al. -
Experimental Assessment of Building Blockage Effects in a Simplified Urban District
Abstract This study presents experimental results of velocity distribution and water depth at specific locations obtained from simplified urban district experiments accounting for the effect of building blockage. Laboratory experiments are performed ...
2016 / Qi Zhou, Wangyang Yu, Albert S. Chen, Chunbo Jiang, Guangtao Fu