Materials engineering topic list of research papers
-
Comparison and Analysis of Institutionalization, Standardization and Normalization of Enterprise Safety Production
Abstract Through the analysis on institutionalization, standardization and normalization concepts, to clarify the management focus and use object of institutionalization, standardization and normalization of safety production, and propose...
2012 / Wang Yongyi, Zhang Yan -
Preparation of Bimetallic Core-shell Nanoparticles with Magnetically Recyclable and High Catalytic Abilities
Abstract In this work, we report the preparation of bimetallic core-shell nanoparticles (NPs) using a simple solution synthetic route. A typical example is the Ag@Ni NPs that are synthesized using oleylamine as solvent and reducing agent. The...
2012 / Huizhang Guo, Yuanzhi Chen, Xiaozhen Chen, Laisen Wang, Hemei Ping, et al. -
Development of a Simple-structured Pneumatic Robot Arm and its Control Using Low-cost Embedded Controller
Abstract The purpose of our study is to develop the flexible and lightweight actuator and apply it into a flexible robot arm. In this paper, the master-slave attitude control and the trajectory control of the flexible robot arm are proposed. This...
2012 / Mohd Aliff, Shujiro Dohta, Tetsuya Akagi, Hui Li -
Post on the Issue of Safety of Steel Structures of Hot Dip Galvanized Structural Components
Abstract Worldwide, the majority of newly built steel structures are protected against corrosion by hot dip galvanizing. The coating is applied by immersion of steel parts in molten zinc at a temperature around 450°C. Components supplied for coating ...
2012 / V. Kuklik -
Ethylene Dimerization by a Homogeneous Ti-Based Three-Component Catalyst System: Process Evaluation and Optimization of Parametric Performance
Abstract This research utilizes the design of experimental (DOE) methodology by Taguchi orthogonal array (OA) to optimize various operating parameters of a Ti-based homogeneous catalyst in presence of the mixture of two modifiers and...
2012 / S. Hamed Mahdaviani, M. Parvari, D. Soudbar -
Area Overhead and Power Analysis of March Algorithms for Memory BIST
Abstract The power dissipation has become a serious concern in VLSI testing with the increasing in number of embedded memories in a System-on-Chip (SoC). Memory Built in Self Test (MBIST) uses fault-oriented algorithms, such as March test algorithm...
2012 / Balwinder Singh, Arun Khosla, Sukhleen Bindra Narang -
Large and Small Scale Materials Testing of HT-9 Irradiated in the STIP Irradiation Program2010 / P. Hosemann, Y. Dai, E. Stergar, H. Leitner, E. Olivas, et al.
-
Binders Based on Natural Anhydrite and Modified by Finely-Dispersed Galvanic and Petrochemical Waste
Abstract In the present paper the experimental research dedicated to derivation of anhydrite binders with improved physical and mechanical properties. The positive influence of dispersed additives to technological properties of anhydrite...
2013 / Stanislav Sychugov, Yuriy Tokarev, Tatiana Plekhanova, Anastasia Kazantseva, Dinara Gaynetdinova -
Structural Control and Chemical Functionalization of Dual-Layer Nanofiltration Hollow Fiber Membranes for Efficient Waste Water Treatment2012 / S.P. Sun, S.Y. Chan, T.S. Chung
-
Influence of Cutting Interactions on Cutting Force of a Pick
Abstract Various mechanical excavators have been used for rock cutting. The cutting drum of an excavation machine normally consists of a large number of cutting picks. Accurate calculation of cutting force on individual picks is important to machine ...
2013 / Yong Sun, X.S. Li -
Numerical Simulation on the Flow State of Dross Layer in Tundish
Abstract In tundish, the flow state of top dross layer not only influences the oxidation of the molten steel, but also is directly related to the floating and adsorption of inclusions, and is concerned with the entrainment of steel to...
2013 / Chaoxiang Li, Biao Liu, Shengyu Zhu -
Platinum Nanoparticle Chemical Sensors on Polyimide Substrates
Abstract A gas sensor formed by a Platinum (Pt) nanoparticle film and a poly(2-hydroxyethyl methacrylate) (PHEMA) polymer layer is discussed in this paper. The Platinum nanoparticles which have been produced by a modified magnetron sputtering...
2012 / E. Skotadis, D. Mousadakos, K. Katsabrokou, S. Stathopoulos, D. Tsoukalas -
Manufacture, Qualification and Approval of New Aviation Turbine Fuels and Additives
Abstract Energy consumption has always been instrumental in raising the living standards of the people of this planet. Unfortunately, it is predicted that the fossils fuels which have heretofore been the main source of energy will be practically...
2012 / U. Yildirim, S. Abanteriba -
Effect of Temperature on the Crevice Corrosion Resistance of Ni-Cr-Mo Alloys as Engineered Barriers of Nuclear Repositories
Abstract Deep geological disposal is the strongest alternative to the disposal of high level nuclear waste. Alloys 625, C-22, C-22HS and HYBRID-BC1 are considered among candidates as engineered barriers of nuclear repositories. Localized corrosion,...
2012 / E.C. Hornus, M.A. Rodr’guez -
Roles of compressive residual stress in enhancing the corrosion resistance of nano nitride composite coatings on steel
Abstract Nanocomposite coatings were synthesized, and subsequently annealed, in an attempt to understand the influence of residual stress upon their resistance to corrosion under acidic attack. Pitting corrosion, originating from microscopic coating ...
2013 / Xiaoli Zhao, Paul Munroe, Daryoush Habibi, Zonghan Xie -
Research on centrifugal pump monitoring system based on virtualization technology
Abstract Centrifugal pump's state monitoring and analysis system is a comprehensive system built upon centrifugal pump's performance parameter and historical background. Real-time monitoring and analysis on the running state of marine centrifugal...
2011 / Bo Ning, Xiang-xin Cheng, Shuo Wu -
Investigation of the Material Removal Efficiency During Femtosecond Laser Machining
Abstract Understanding physical processes accompanying ablation is necessary for the optimal use of Femtosecond Laser pulse material processing. The current work describes the implementation of a molecular dynamics based approach, developed for...
2012 / P. Stavropoulos, K. Efthymiou, G. Chryssolouris -
Tele-operation Construction Robot Control System with Virtual Reality Technology
Abstract In this paper, a tele-operation construction robot (TOCR) control system with virtual reality is discussed. The system consists of TOCR driven by hydraulic servo system, two joysticks for controlling the TOCR, and 2-dimensional working...
2011 / Xinxing Tang, Hironao Yamada -
Paradigm for Art Education; Creation Story of Jewels, Theme, Design, Artwork, 3D
Abstract Theme, design artwork and sizing are the main characters for the history of creation in jewelry art. In other words, you can discover a masterpiece in this history of creation. Marmara University, School of Jewellery Technology and Design...
2012 / Leyla Ulusman, Cimen Bayburtlu -
A Novel Solid-State Thermal Rectifier Based On Reduced Graphene Oxide2012 / He Tian, Dan Xie, Yi Yang, Tian-Ling Ren, Gang Zhang, et al.