Chemical engineering topic list of research papers
-
An Investigation on Cocombustion Behaviors of Hydrothermally Treated Municipal Solid Waste with Coal Using a Drop-Tube Reactor2012 / Liang Lu, Yuqi Jin, Masato R. Nakamura, Marco J. Castaldi, Kunio Yoshikawa
-
Effect of Al-Cu Bimetallic Components in a TiO2 Framework for High Hydrogen Production on Methanol/Water Photo-Splitting2012 / A-Young Kim, Misook Kang
-
Calorimetric and Rheological Measurements of Three Commercial Thermosetting Prepreg Epoxies2006 / M. Hargis
-
Nanocrystalline N-Doped TiO 2 Powders: Mild Hydrothermal Synthesis and Photocatalytic Degradation of Phenol under Visible Light Irradiation2013 / Junna Xu, Feng Wang, Wenxiu Liu, Wenbin Cao
-
Droplet/ligament modulation of local small-scale turbulence and scalar mixing in a dense fuel spray
Abstract In this study, the modulation of turbulence and scalar mixing by finite-size droplets/ligaments in a dense fuel spray is investigated using a DNS (Direct Numerical Simulation) dataset. Ejected from a spray nozzle with a high speed, a...
2014 / J. Shinjo, J. Xia, A. Umemura -
The Way of Increasing Resource Efficiency of Naphtha Reforming Under Conditions of Catalyst Acid and Metal Activity Balance by Mathematical Modeling Method
Abstract Industrial bifunctional reforming catalysts are promoted by chlorides for providing adequate acid activity in izomerization and dehydrocyclization reactions. Chlorine content on the reforming catalyst surface is not only the most important, ...
2015 / A.G. Koksharov, E.D. Ivanchina, S.A. Faleev, A.I. Fedyushkin -
Investigation of wax precipitation in crude oil: Experimental and modeling
Abstract In this work, a series of experiments were carried to investigation of rheological behavior of crude oil using waxy crude oil sample in the absence/presence of flow improver such as ethylene-vinyl acetate copolymer. The rheological data...
2015 / Taraneh Jafari Behbahani, Aliakbar Miranbaygi, Zahra Taheri, Bahram Ghambari -
Application and Operating Experience of Sintered Metal Fiber Hot Gas Filters for FCC Unit
Abstract A long-term test was performed in a Fluid Catalytic Cracking (FCC) hot gas filtration facility using sintered metal candle filters. The operating temperature and pressure were maximum 550°C and 0.28MPa respectively. Specific particles...
2015 / Liang Yang, Zhongli Ji, Xiaolin Wu, Weiwei Ma -
Gas Hydrate Stability and Sampling: The Future as Related to the Phase Diagram2010 / E. Dendy Sloan, Carolyn A. Koh, Amadeu K. Sum
-
Computational solutions for non-isothermal, nonlinear magneto-convection in porous media with hall/ionslip currents and ohmic dissipation
Abstract A theoretical and numerical study is presented to analyze the nonlinear, non-isothermal, magnetohydrodynamic (MHD) free convection boundary layer flow and heat transfer in a non-Darcian, isotropic, homogenous porous medium, in the presence...
2015 / O. Anwar Bég, S. Abdul Gaffar, V. Ramachandra Prasad, M.J. Uddin -
Preparation of Silicon Oxide Coated KS-6 Graphite Composite Anode Materials by Sol-gel Method in Lithium Ion Batteries
Abstract This work reported a sol-gel preparation method for the SiO2 coated KS-6 composite anode material by using KS-6 graphite, silicon oxide, and glucose (C6H12O6). Silicon oxide was used as a surface modification dopant and C6H12O6 was used as...
2015 / Chun-Chen Yang, Jeng-Ywan Shih, Min-Yen Wu -
CFD simulations of influence of steam in gasification agent on parameters of UCG process
Abstract Underground coal gasification (UCG) is considered to be a perspective and constantly developing technology. Nevertheless it is a very complex and technically difficult process, which results depend on many variables. Mathematical models...
2015 / Alina Żogała, Tomasz Janoszek -
Electrochemical Performance of Ni1-xCox-GDC Cermet Anodes for SOFCs
Abstract Electrochemical performance of Ni1-xCox-GDC (Gd0.1Ce0.9O1.95) cermet was studied for the use as a novel anode for solid oxide fuel cells (SOFCs). Ni1-xCoxO (x=0.25, 0.5, 0.75) was prepared from NiO and Co3O4 compounds via a solid state...
2013 / Jiratchaya Ayawanna, Darunee Wattanasiriwech, Suthee Wattanasiriwech, Kazunori Sato -
Stochastic Texture Analysis for Measuring Sheet Formation Variability in the Industry2006 / J. Scharcanski
-
Coal-CO2 Slurry Feed for Pressurized Gasifiers: Slurry Preparation System Characterization and Economics
Abstract Gasification-based plants with coal-CO2 slurry feed are predicted to be more efficient than those with coal-water slurry feed. This is particularly true for high moisture, low rank coal such as lignite. Nevertheless, preparation of the CO2...
2013 / Cristina Botero, Randall P. Field, Howard J. Herzog, Ahmed F. Ghoniem -
Techno-economic analysis and life-cycle assessment of cellulosic isobutanol and comparison with cellulosic ethanol and n-butanol2013 / Ling Tao, Eric C. D. Tan, Robert McCormick, Min Zhang, Andy Aden, et al.
-
Evaluation of Calcium Looping as Carbon Capture Option for Combustion and Gasification Power Plants
Abstract Power generation is one of the industrial sectors with major contribution to greenhouse gas emissions (especially CO2). For climate change mitigation, a special attention is given to the reduction of CO2 emissions by applying capture and...
2014 / Calin-Cristian Cormos, Letitia Petrescu -
Assessment of Fire Risk of Gas Pipeline Leakage in Cities and Towns
Abstract The accident risk of gas pipeline leakage in cities and towns and fire risk characteristics of pressure gas pipeline leakage were analyzed. Combined with an example of pressure gas pipeline project in a certain town, the gas pipeline...
2012 / Zhenghua Huang, Jianhua Li -
A crystallization plate for controlling evaporation in hanging drops2004 / Gweneth A. Nneji, Naomi E. Chayen
-
Thermodynamic and Experimental Analysis of a Biomass Steam Power Plant: Critical Issues and their Possible Solutions with CCGT Systems
Abstract This paper shows the experimental and numerical analysis of a biomass steam power plant from maximum power of 2.3 MW with a maximum pressure of 48bar and a turbine inlet temperature of about 430°C at the design point. The analysis has been...
2014 / A. Gimelli, A. Luongo