Scholarly article on topic 'Enhancement of Biodiesel Production from Marine Alga, Scenedesmus sp. through In Situ Transesterification Process Associated with Acidic Catalyst'

Enhancement of Biodiesel Production from Marine Alga, Scenedesmus sp. through In Situ Transesterification Process Associated with Acidic Catalyst Academic research paper on "Chemical sciences"

CC BY
0
0
Share paper
Academic journal
BioMed Research International
OECD Field of science
Keywords
{""}

Academic research paper on topic "Enhancement of Biodiesel Production from Marine Alga, Scenedesmus sp. through In Situ Transesterification Process Associated with Acidic Catalyst"

Hindawi Publishing Corporation BioMed Research International Volume 2014, Article ID 391542, 11 pages http://dx.doi.org/10.1155/2014/391542

Research Article

Enhancement of Biodiesel Production from Marine Alga, Scenedesmus sp. through In Situ Transesterification Process Associated with Acidic Catalyst

Ga Vin Kim,1 WoonYong Choi,2 DoHyung Kang,3 ShinYoung Lee,1 and HyeonYong Lee4

1 Department of Bioengineering and Technology, College of Engineering, Kangwon National University, Chuncheon 200-701, Republic of Korea

2 Department of Medical Biomaterial Engineering, Kangwon National University, Chuncheon 200-701, Republic of Korea

3 Korea Institute of Ocean Science & Technology (KIOST), Gyeonggi-do, Ansan-si, P.O. Box29, Seoul 426-744, Republic ofKorea

4 Department of Food Science and Engineering, Seowon University, Cheongju, Chungbuk 361-742, Republic of Korea

Correspondence should be addressed to ShinYoung Lee; sylee@kangwon.ac.kr and HyeonYong Lee; hyeonl@seowon.ac.kr Received 8 November 2013; Revised 16 December 2013; Accepted 17 December 2013; Published 13 February 2014 Academic Editor: Kannan Pakshirajan

Copyright © 2014 Ga Vin Kim et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

The aim of this study was to increase the yield of biodiesel produced by Scenedesmus sp. through in situ transesterification by optimizing various process parameters. Based on the orthogonal matrix analysis for the acidic catalyst, the effects of the factors decreased in the order of reaction temperature (47.5%) > solvent quantity (26.7%) > reaction time (17.5%) > catalyst amount (8.3%). Based on a Taguchi analysis, the effects of the factors decreased in the order of solvent ratio (34.36%) > catalyst (28.62%) > time (19.72%) > temperature (17.32%). The overall biodiesel production appeared to be better using NaOH as an alkaline catalyst rather than using H2SO4 in an acidic process, at 55.07 ± 2.18% (based on lipid weight) versus 48.41 ± 0.21%. However, in considering the purified biodiesel, it was found that the acidic catalyst was approximately 2.5 times more efficient than the alkaline catalyst under the following optimal conditions: temperature of 70°C (level 2), reaction time of 10hrs (level 2), catalyst amount of 5% (level 3), and biomass to solvent ratio of 1: 15 (level 2), respectively. These results clearly demonstrated that the acidic solvent, which combined oil extraction with in situ transesterification, was an effective catalyst for the production of high-quantity, high-quality biodiesel from a Scenedesmus sp.

1. Introduction

Biodiesel is an alternative renewable fuel that is derived from vegetable oils, animal fats, spent frying oils, and microbial oils. This fuel can replace petroleum-based fuels and can be used in all types of the currently available diesel engines without them being modified [1, 2].

Extensive investigation of biodiesel manufacturing has been conducted using oil-like materials, such as vegetable oils, animal fats, and used frying oils, which are limited by their availability, and the prices of these materials are more greatly sensitive to the industrial demands for oil. The limited inventories also created a fuel versus food issue that requires consideration of non-food-related feedstock. Therefore, some attempts have been made to produce biodiesel

from nonedible resources such as spent frying oils, greases, and Jatropha. However, a major criticism of large-scale fuel production from nonedible resources is that vast areas of farmland or native habitats will be consumed, and food prices will increase. Because of these problems, microalgae are currently considered one of the most promising resources for biodiesel production [3-6].

Microalgae exhibit a high photosynthetic efficiency and a strong capacity to adapt to the environment (e.g., high salinity, heavy metal ion content, presence of toxicants, and high CO2 concentration). Moreover, microalgae can be grown in various climates and on nonarable land, including marginal areas that are unsuitable for agricultural purposes (e.g., desert and seashore lands). The growth of microalgae in liquid medium can be controlled easily, and they can be

cultured in nonpotable water. Moreover, most microalgae (e.g., Scenedesmus and Chlorella) have very short cell cycles (less than 24 hours) and high oil productivity per hectare. Therefore, microalgae have been predicted to be a newbiofuel source that is renewable and is environmentally and economically sustainable [3, 6-9].

Many species of microalgae suitable for producing fuel oil have been identified, that is, Chlorella, Scenedesmus, Spir-ulina, and Nostoc spp. Supplementation of iron to the growth medium under nitrate limitation was found to raise the crude lipid content of Chlorella to ~56.6% (dry cell weight). The lipid content of Scenedesmus obliquus reached up to ~58.3% (dry cell weight) when lower nitrogen-supplemented medium was utilized [10-13]. In our preliminary studies [14, 15], Scenedesmus sp. was shown to be an appropriate source for biodiesel by determining its lipid composition and extraction yield. Therefore, we decided to use this species as a biodiesel feedstock in the present study.

FAMEs (fatty acid methyl esters) are produced via a transesterification process that involves a chemical reaction between triglycerides and an alcohol, generally methanol, in the presence of a catalyst [16,17]. This process is the one that is most commonly used to produce industrial biodiesel due to the low cost of the catalyst, its utility in mass production, and its high productivity. However, this method often produces a large amount of hazardous solvent waste and is generally cumbersome. This transesterification process requires preex-tracting the oil from the raw materials. Automated extraction equipment has been successfully developed, but it requires a longer extraction process [6,18,19].

Recently, an in situ transesterification (or direct transesterification) method that may overcome these limitations has attracted attention. In situ transesterification differs from the conventional method because the oil-bearing material directly contacts the acidified or alkalized alcohol instead of preextracted oil reacting with the alcohol. Thus, the extraction and transesterification processes occur in the same step. The alcohol acts as both an extraction solvent and an ester-ification reagent, which could reduce the production time associated with preextracting the oil and maximize the fatty acid ester yield. By using such reagents, the amount of solvents and the processing period are reduced and the problems of waste disposal are avoided [17, 20, 21].

The most conventional approach to experiment design is to optimize one variable (or one factor) at a time in single-response problems. An increasing number of factors increases the number of design experiments. However, the increasing complexity of product design is such that at least two quality characteristics are frequently simultaneously considered to improve the product quality. Moreover, correlations among multiple responses always exist and may generate conflicts among the optimal parameter settings. Hence, simultaneously optimizing a multiresponse problem is important [22].

The Taguchi method is a powerful experimental design tool that provides a simple, effective, systematic approach to determining the optimal parameters. Furthermore, this approach requires minimum experimental cost and it efficiently reduces the effect of the sources of variation [23]. The design

of experiments (DOE) methodology of the Taguchi orthogonal array (OA), a factorial-based approach, has recently become exceeding important due to its application in optimizing biochemical processes [24].

In this biodiesel research study, we investigated using microalgae as the feedstock for biodiesel production. A microalgal Scenedesmus sp. was selected for biodiesel production through in situ transesterification via acidic catalysis and the synthesis of this biofuel was optimized using the Taguchi method.

2. Materials and Methods

2.1. Materials. Freeze-dried microalgal cells were provided by KORDI (Korea Ocean Research & Development Institute). The microalga was cultured under controlled conditions, and the algal biomass was harvested by centrifugation at 3000 rpm for 10 min. The cells were then freeze-dried, ground (100 mesh), and stored in the freezer. The freeze-dried powder was kept under desiccation of anhydrous sodium sulfate (Daejung Co., Ltd, Shi heung, Korea) overnight, before use.

2.2. In Situ Transesterification via Alkaline or Acidic Catalysis. The in situ transesterification process following the method of Ehimen et al. [25] was conducted at the laboratory scale. The alkaline process experiments were conducted under the following conditions: reaction time of 1 to 3hrs, reaction temperature of 40 to 60°C, quantity of the reacting alcohol (methanol, 99.5%, Daejung Co. Ltd, Shi Heung, Korea) of 20 to 50 mL, and concentrations of sodium hydroxide of 0.5 to 1.5% (w/w of lipid). The reactor had a capacity of 250 mL, and it was immersed in a water bath to maintain the reaction temperature at the desired level. The reaction was conducted under reflux conditions to minimize the solvent loss. The acidic process experiments were conducted under the following conditions: reaction time of 5 to 15 hrs, reaction temperature of 50 to 90°C, biomass to solvent ratio of 5: 1 to 25: 1 (v/w), and concentrations of sulfuric acid of 1 to 5% (v/v of solvent). The reactor capacity was 500 mL. A freeze-dried algal biomass (15 g) was mixed with methanol in which sulfuric acid had been dissolved. The scheme of the in situ transesterification reaction and product purification steps are shown in Figure 1. Additionally, a freeze-dried algal biomass (5 g) was mixed with methanol in which 0.5% NaOH had been dissolved as an alkaline catalyst. Thus, the acidic catalyst of 5% H2SO4 was replaced with sodium hydroxide. The reactor containing the reaction mixture was heated and then maintained at the temperature of interest for the specified periods. After the in situ transesterification step, the reaction flask was allowed to stand for 1 hour to allow its contents to settle. The reaction mixture was filtered (Advantec No. 2, Toyo Roshi Inc., Tokyo, Japan) and the residues were washed twice by resuspension in methanol (10 mL) for 10 min to recover any traces of FAME products from the residues. Distilled water (15 mL) was added to the filtrate to facilitate the separation of the hydrophilic components of the extract. This mixture was centrifuged (5000 xg) for 15 min and then transferred to a separation funnel. Further extraction of the FAME products was achieved by three times for

Freeze dried microalgae

Met-OH (75~225 mL) Temperature (50~90°C)

H2 SO4 (0.75~18.75 mL)

Time (5~15 hr)

Acid ---> catalyst

Alkali

catalyst < -

Reaction

Met-OH (20~50 mL) Temperature (20~60°C) NaOH Time (1~3 hr)

Filtration

3 times ' ; 15 min "

Hydrophobic layer: hexane + FAME + glycerides

Filtrate

DW (15 mL)-----I

- Hexane (10 mL)--->4,

Centrifugation

5000 xg, 15 min

Phase separation

Upper layer

Neutralization Filtration

Evaporation

Weighed

Lower layer

2 times ; 10 min

with DW Overnight under anhydrous sodium sulphate

40° C

Filter cake ; biomass

I----Met-OH (10 mL)

Suspension ---------

Water layer: glycerol + catalyst + excess methanol

Figure 1: A schematic diagram of the in situ acidic and alkaline transesterification reactions.

15 min extractions using 10 mL of hexane. The pooled hexane layer was washed with water (to remove the residual traces of the acidic catalyst and methanol), separated, and then dried over anhydrous sodium sulfate overnight. The extracted solvent layer was filtered (Advantec No. 2, Toyo Roshi Inc., Tokyo, Japan), and its volume was recorded. An aliquot of the extraction solvent (10 mL) containing the FAMEs (crude biodiesel) was transferred to a preweighed glass vial evaporated (40~45°C) for 15 min using a vacuum evaporator (EYELA, Digital Water Bath SB-1000, Japan) and then cooled within a desiccator for 30 min. The mass of the biodiesel was determined gravimetrically, in duplicate. All of the stirred reactions were conducted using a magnetic stirrer system with a constant rotation speed of 500 rpm. The biodiesel yield from the algae oil was calculated using (1) as follows:

Biodiesel yield (%)

Algae mass (g) x Lipid content (%) (1)

= Weight of biodiesel (FAME) (g) '

in which the amount of FAMEs at each step was determined by collecting them from a TLC plate and weighing them.

2.3. Thin Layer Chromatography (TLC) Analysis. After transesterification, the FAMEs (fatty acid methyl esters (FAME)) and residual triacylglycerides (TAGs) were measured using 0.25 mm thick silica gel G-60 TLC plates (Merck, Darmstadt,

Germany). The detailed method was as follows: the elution solvent was n-hexane: diethyl ether (90: 10, v/v) and after full development to the detection of the FAME spots, the spots were visualized using an iodine vapor and spraying the plates with 10% phosphomolybdic acid (98% purity, Daejung Co., Ltd, Shi Heung, Korea) in ethanol, and then drying them in the oven at 105°C [26]. The mono-, di-, and triglyceride mixture (TAG STD, Supelco, Bellefonte, PA, USA) and commercial biodiesel (FAME, S Company Houston, TX, USA) were used as standards [26]. Additionally, the pigments that remained in the FAME fraction were also separated by TLC, using the same 0.25 mm thick silica gel G-60 plates (Merck, Darmstadt, Germany) that were developed using petroleum ether (99.5%, Daejung Co., Ltd, Shi Heung, Korea) : cyclo hexane (%, Wako, Osaka, Japan): ethyl acetate (99%, Daejung Co., Ltd, Shi Heung, Korea) : acetone (99.5%, Daejung Co., Ltd, Shi Heung, Korea) : methanol (99.5%, Daejung Co., Ltd, Shi Heung, Korea) (60 :16:10:10:4, v/v) [27].

2.4. Purification of FAMEs. The FAMEs of the crude biodiesel were purified using silica gel column chromatography. The crude biodiesel was applied to a silica gel chromatography column. The column had been prepared using the previously described slurry of silica gel (18 g) (0.063-0.2 mm, Merck, Darmstadt, Germany) in hexane (300 mL). The n-hexane level was lowered until it was 1 cm above that of the stationary phase. The extracted algal oil was added to the column and eluted using n-hexane: EtOAC (25: 1, v/v) at a flow rate of

3mL/min. The FAME fraction had a deep yellow color [28, 29].

2.5. Design of the Experiments: Taguchi Method. Experiments were designed to determine the effects of four factors, the reaction temperature, the reaction period, the amount of catalyst (H2SO4), and the biomass to solvent ratio. Nine experiments were designed using the Taguchi method with an L9 three-level-four-factor array [34].

2.6. Analysis of the FAME Fatty Acid Profiles. To determine the fatty acid composition of the FAMEs, gas chromatography (GC, HP 6890 series, Victoria, Australia) was conducted using the following method: 1 ^L of FAME that was obtained using in situ transesterification via alkaline or acidic catalysis was injected into a GCwith a flame ionization detector (FID); an SP-2560 column (100 m x 0.25 mm x 0.2 pm, #24056, Supelco); and an oven temperature that increased at 4°C/min from 100°C to 240°C. The pouring and detector temperatures were set at 250°C and 280°C, respectively, the flow volume was 1.0 mL, and the split ratio was 50 : 1 [30].

2.7. Statistical Analysis. The data are expressed as the mean values ± SDs (standard deviation) and the mean values are the averages of five test results per experiment. The data were analyzed using the Student's i-test (SAS 9.1, SAS, Cary, NC, USA). The experiments were repeated at least three times to confirm the results. The data were analyzed using an analysis of variance, and the mean values were considered significantly different at P < 0.05. The optimal extraction condition was determined using regression analysis.

3. Results and Discussion

3.1. Optimization of Crude Biodiesel Production Using an Alkaline or Acidic Catalyst. For conventional two-step industrial biodiesel production, methanol is most often used as the reaction solvent with an alkaline catalyst for transesterifica-tion because it has several advantages over the simultaneous separation of glycerol, a high product yield, and low price [31], as well as mild processing conditions, short reaction times, and some other economic benefits [32-34]. Rather than this conventional transesterification process, in situ transesteri-fication with an alkaline catalyst could be used; however, for the production of biodiesel from microalgae, an alkaline catalyst would not be suitable for the in situ transesterification process, due to the characteristically high FFA (free fatty acid) content of the microalgal lipids. In situ transesterification of oils containing high concentrations of FFA would result in a partial saponification reaction, leading to soap formation [25]. Soaps can cause the formation of emulsions, which create difficulties in the downstream recovery and purification of the biodiesel [35]. Using inorganic acids, such as hydrochloric acid and sulfuric acid, as reaction catalysts was therefore considered for microalgal lipid transesterification, due to their insensitivity to the FFA content of this lipid feedstock. Consequently, using acidic catalysis facilitates both the biodiesel producing transesterification and esterification

Table 1: Experimental factors and levels for the orthogonal array design using the Taguchi method (% w/w, based on the lipid weight).

Temperature Time Catalyst amount Solvent

Level (°C) (hr) (% of algal weight, w/w) (mL)

A B C D

1 30 1 0.5 20

2 45 2 1 35

3 60 3 1.5 50

Run number A B C D Y (%)

1 1 1 1 1 11.63 ± 1.06

2 1 2 2 2 31.33 ±0.79

3 1 3 3 3 33.29 ± 0.47

4 2 1 2 3 37.08 ± 0.58

5 2 2 3 1 38.13 ±2.32

6 2 3 1 2 48.54 ± 2.99

7 3 1 3 2 50.07 ± 1.02

8 3 2 1 3 55.07 ±2.18

9 3 3 2 1 40.89 ± 2.07

reactions [25]. Studies of the catalytic activities of HCl and H2SO4 in the transesterification of Thevetia peruviana seed oil, cotton seed oil, and vegetable oil, among others, showed that H2SO4 exhibited better catalytic activity than HCl [36, 37]. Therefore, for in situ transesterification using an alkaline or acidic catalyst, several reaction parameters should be considered such as the reaction temperature, the reaction time, the amount of catalyst, the amount of solvent, the water content, and the agitation speed [36, 37]. To obtain the highest yield of biodiesel, these variables were optimized using the Taguchi methods [38], employing an L9 three-level-four-factor orthogonal array matrix [34]; nine experiments were designed as shown in Tables 1 and 3 for an alkaline or an acidic catalyst, respectively. Using an alkaline catalyst, as shown in Table 1, the biodiesel yield was the lowest and the highest in experiment number 1 and experiment number 8, respectively. Depending on the level of each factor, the yields changed from 11.63 ± 1.06 to 55.07 ± 2.18% and the average yield was 38.45 ± 1.50%. In each factor level (A;) of the yield (K,A) and at each Kf value per unit level, the (= -KA/3) were calculated from the difference (.R value) between the maximum Kf and minimum However, as shown in Table 3, the lowest and highest yields of crude biodiesel were obtained in experiment number 1 and experiment number 7, respectively. Depending on the level of each factor, the yields were changed from 13.03 ± 3.07 to 48.40 ± 0.51% and the average yield was 39.27 ± 0.94%. The factor effects decreased in the order of biomass to solvent ratio (34.36%) > catalyst amount (28.62%) > reaction time (19.72%) > reaction temperature (17.32%). From these factors, the size of the effect of the test parameters could be calculated, as shown in Tables 2 and 4. Table 2 shows the effect of the reaction factors on the mean response using the alkaline catalyst. The effect refers to

Table 2: Analysis of the in situ transesterification factors for the yield of crude biodiesel from Scenedesmus sp. using the orthogonal array design (% w/w, based on the lipid weight).

A B C D

76.25 ±2.3 98.78 ± 2.7 115.21 ±6.2 90.65 ± 5.4

K2 123.75 ±5.9 124.51 ± 5.3 109.31 ±3.4 129.94 ± 4.8

146.01 ± 5.3 122.72 ± 5.5 121.49 ±3.8 125.42 ± 3.2

25.42 ± 0.77 32.93 ± 0.88 38.4 ±2.07 30.22 ± 1.82

k2 41.25 ± 1.96 41.5 ± 1.76 36.44 ± 1.14 43.31 ± 1.60

fc3 48.67 ± 1.75 40.91 ± 1.84 40.5 ± 1.27 41.81 ± 1.08

R 23.25 8.58 4.06 13.09

Optimal level 3 2 3 2

Kf =£ biodiesel yield at At. k? = Kfl 3.

Rf = maxjfcf} - minjfcf}.

Table 3: Experimental factors and levels for the orthogonal array design usingthe Taguchi method (% w/w, based on the lipid weight).

Temperature Time Catalyst amount Biomass to solvent

Level (°C) (hr) (% of solvent, v/v) ratio (mL, v/w)

A B c D

1 50 5 1 1:5

2 70 10 3 1:15

3 90 15 5 1:25

Run number A B c D 7 (%)

1 1 1 1 1 13.03 ± 3.07

2 1 2 2 2 44.72 ±0.18

3 1 3 3 3 44.13 ± 0.34

4 2 1 2 3 40.38 ± 0.36

5 2 2 3 1 39.36 ± 0.82

6 2 3 1 2 44.46 ± 1.08

7 3 1 3 2 48.40 ± 0.51

8 3 2 1 3 39.80 ± 1.65

9 3 3 2 1 39.07 ± 0.42

the average value of the crude biodiesel yield for each factor at the different levels. Thus, the average value for each factor at each of the three levels was calculated and plotted (Figure 2). Figure 2 shows the mean effects plot for the crude biodiesel yield of in situ transesterification via alkaline catalysis. The dots in the reaction time, amount of catalyst, and solvent quantity show the fluctuations in the biodiesel yield. The lowest biodiesel yield was obtained at the lowest reaction temperature; increasing the reaction temperature resulted in a higher biodiesel yield. The effects of the factors decreased in the order of reaction temperature (47.5%) > solvent quantity (26.7%) > reaction time (17.5%) > catalyst amount (8.3%). The optimal levels of each factor were obtained from the value of ki , and these results lead to the conclusion that the factors that provided the maximal yield were a reaction temperature of 60° C, a solvent quantity of 35 mL, a reaction

time of 2 hrs, and an amount of catalyst of 1.5% (based on the lipid weight). However, the effects of the reaction time and the amount of catalyst were weaker than that of the other factors. Therefore, the levels of the recommended factors were as follows: reaction temperature of 60°C (level 3), a solvent quantity of 35 mL (level 2), reaction time of 2 hrs (level 2), and an amount of catalyst of 0.5% (level 1). The theoretical biodiesel yield of 55.07 ± 2.18% (P < 0.05) could be obtained using these optimal conditions. Figure 3 shows the mean effects plot for the crude biodiesel yield from in situ transesterification via acidic catalysis. The dots in biomass to solvent ratio showed the fluctuations of the biodiesel yield. When the levels of the reaction temperature, reaction time, and amount of catalyst increased, a higher biodiesel yield was obtained. The lowest biodiesel yield was obtained at the lowest biomass to solvent ratio, and the highest biodiesel yield was obtained at the middle level of the biomass to solvent ratio. The optimal levels of each factor were obtained from the value of ki , and these results lead to the conclusion that the factors that provided the maximum yield were a reaction temperature of 90°C, a reaction time of 15 hrs, an amount of catalyst of 5% (base on solvent), and a biomass to solvent ratio of 1: 15 (w/v). However, the time and temperature effects were lower than that of the other factors, and these conditions were not favorable for biodiesel production. A high reaction temperature increases the cost of biodiesel production [16]. A long reaction time also increases the cost of production [39]. Therefore, a reaction temperature of 70°C (level 2), a reaction time of 10 hrs (level 2), an amount of catalyst of 5% (level 3), and a biomass to solvent ratio of1: 15 (level 2) were selected as the optimal conditions. A crude biodiesel yield of 48.41 ± 0.21% (P < 0.05) could be obtained under these optimal conditions. The optimal conditions provided almost the same yield of biodiesel as the maximal conditions.

3.2. Identification and Purification ofFAMEs. Thin layer chromatography (TLC) is one of the simplest and most widely used methods for separating mixtures for analysis. In this study, it was used to monitor the conversion of the algal lipids to fatty acid methyl esters (FAMEs, namely, biodiesel). The TLC results demonstrated the presence of FAME, TAG, and

Table 4: Analysis of the in situ transesterification factors for the yield of crude biodiesel from Scenedesmus sp. using the orthogonal array design (% w/w, based on lipid weight).

A В С D

102.13 ±3.61 102.03 ± 4.46 97.26 ± 7.04 91.46 ±4.71

K2 124.24 ± 2.00 124.14 ±2.77 124.50 ± 1.33 137.97 ± 1.13

Кз 127.42 ± 2.61 127.63 ± 0.99 132.04 ±0.16 124.38 ± 2.38

34.04 ± 1.20 34.01 ± 1.49 32.42 ± 2.35 30.49 ± 1.57

k2 41.41 ± 0.67 41.38 ±0.92 41.50 ±0.44 45.99 ± 0.38

fc3 42.47 ± 0.87 42.54 ± 0.33 44.01 ± 0.05 41.46 ±0.79

R 8.43 ± 0.24 8.54 ± 1.16 11.59 ±2.40 15.50 ± 1.60

Optimal level 3 3 3 2

Kf =£ biodiesel yield at At. kf = Kf/3.

Rf = maxjfcf} - minjfcf}.

H 40 -

Temperature (° C) (a)

Catalyst amount (w/w, %)

"Ï 50 (%,

Time (hr) (b)

Solvent quantity (mL) (d)

Figure 2: Main effects plot for the reaction factors in in situ transesterification via alkali catalysis.

free fatty acids. The TAG standard was a mixture of mono-, di-, and triglycerides, and the FAME standard was a commercial biodiesel (as a comparative standard). Each standard was eluted using n-hexane. The retention factors for methyl ester and triglycerides were calculated as .R^, Me = 0.7-0.73 and .Ry, TAG = 0.41-0.45, respectively. The compound with the larger Rj is less polar because it interacts less strongly

with the polar adsorbent on the TLC plate. Here, the methyl esters and triglycerides exhibited the characteristics of high nonpolarity. As shown in Figure 4, after the TLC plates had been developed, a dark trace appeared only in the alkaline catalyzed biodiesel, which was green before the visualization reaction was performed. The photosynthetic microalga Scenedesmus sp. synthesizes pigments such as chlorophylls

Temperature (°C) (a)

Catalyst amount (% of solvent v/v)

£ 35 -

1? 45-

Time (hr) (b)

1:15 1:25

Solvent ratio (v/w of biomass)

Figure 3: Main effects plot for the reaction factors in in situ transesterification via acidic catalysis.

and carotenoids. The dark green trace was considered to contain pigments. TLC was used to identify the pigments, which consisted of chlorophyll a, ^-carotene, pheophytin a and b, and other substances (Figure 5) [27]. Silica gel column chromatography of crude alkali-catalyzed biodiesel was used to fractionate the pigments and the FAMEs. The column was eluted with n-hexane: acetone (98.5:1.5, v/v). As shown in Figure 6(a), three fractions were obtained from the crude alkali-catalyzed biodiesel. The eluted materials were collected in individual vials and were fractionated depending on the color and weight difference between these vials. Fraction A (tube numbers 1-10) was colorless and transparent, but the colors of fraction B (tube numbers 11-16) and fraction C (tube numbers 17-24) were deep yellow and pale yellow, respectively. The green-pigmented materials adsorbed to the silica gel inside the column. The organic solvent of each vial was evaporated in a dry oven at 40° C for a few days, and then the vials were weighed. The materials inside the vials were redissolved in hexane and were then collected according to fractionation (fractions A, B, and C). Each of the fractions was analyzed using TLC, and the results are shown in Figure 7. TLC on silica gel plate demonstrated the presence of methyl esters, tri-, di-, and monoglycerides and fatty acids in the alkali-catalyzed biodiesel (Figure 7). FAMEs were observed in fractions B and C. Then, we conducted the same experiment using acid-catalyzed biodiesel. The color of fraction A (tube numbers 1-12) was colorless and transparent, but the colors of fraction B (tube numbers 13-23) and

fraction C (tube numbers 24-27) were deep yellow and pale yellow (almost colorless), respectively (Figure 6(b)). The materials inside the vials were redissolved in hexane, and then each fraction was collected (fractions A, B, and C). Each fraction was analyzed using TLC, and the results are shown in Figure 8. FAMEs were observed in fraction B. The FAME fraction was purified using silica gel column chromatography, and the purified FAME contents were found to be 29.15% in the crude alkali-catalyzed biodiesel and 83.52% in the acid-catalyzed biodiesel. Approximately 70% of the alkali-catalyzed biodiesel and 16% of the acid-catalyzed biodiesel were found to contain pigments, which consisted of ^-carotene, chlorophyll a, pheophytin a and b, and other substances (Figure 5). Therefore, the final purified biodiesel yields obtained from alkali- and acid-catalyzed biodiesel were estimated to be 16.05% and 40.43%, respectively. The yield of the acid-catalyzed biodiesel was approximately 2.5fold higher than that of the alkali-catalyzed biodiesel. The yield from in situ transesterification using an acidic catalyst appeared to be higher than other reported data obtained using the conventional Taguchi method by 27.9~42.6% [4042]. To evaluate the quality of the biodiesel obtained using these processes, the contents of the major fatty acid in the FAME profiles were estimated, as shown in Table 5. In general, there was not much difference in the fatty compositions of the acidic and alkaline catalyzed analytes; however, higher amounts of C16:0 and C18:3, the two major fatty acids among the FAMEs, were obtained using acidic

DiMono-

(A) (B) (C) (D)

DiMono-

(A) (B) (C) (D)

(a) (b)

Figure 4: Thin layer chromatograms of crude FAMEs on HPTLC plates that were developed using n-hexane: ether (90:10, v/v) and visualized using (a) 10% phosphomolybdic acid in ethanol and (b) iodine vapor. (A) FAMEs (standard); (B) TAGs (standard); (C) in situ transesterification via alkaline catalysis; (D) in situ transesterification via acidic catalysis.

(A) (B)

(a) (b)

Figure 5: Results of separating the pigment fractions using TLC (20 times dilution with hexane). (a) Before development; (b) after development; (A) crude biodiesel; (B) purified biodiesel.

catalysis, which implies that acidic catalysts can produce better quality biodiesel. These results indicated that the acidic catalyst was a more efficient catalyst than the alkaline catalyst for in situ transesterification.

4. Conclusion

To optimize in situ transesterification via alkaline or acidic catalysis for the production of biodiesel from Scenedesmus sp., several objective variables were analyzed using an L9

orthogonal matrix as follows: the reaction time and temperature and the amounts of catalyst and solvents [34]. In using an acidic catalyst in in situ transesterification, the effects of the factors decreased in the order of biomass to solvent ratio (34.36%) > catalyst amount (28.62%) > reaction time (19.72%) > reaction temperature (17.32%). The maximum yield of 48.41 ± 0.21% (P < 0.05) (based on lipid weight) was obtained at a biomass to solvent ratio of 1: 15, H2SO4 at 5% (% of solvent, v/v), a reaction time of 10 hrs, and a reaction temperature of 70°C. For the alkaline catalyst, the effects of the factors decreased in the order of the reaction temperature

Figure 6: Column chromatographic separation of FAME using an n-hexane: acetone (98.5: 1.5, v/v) solution from (a) alkali- and (b) acid-catalyzed biodiesels.

Di-Mono-

Di-Mono-

(A) (B) (C) (D)

(a) (b)

Figure 7: Thin layer chromatograms of the FAME fraction on HPTLC plates that were developed using n-hexane: ether (90: 10, v/v) and visualized using (a) 10% phosphomolybdic acid in ethanol (b) and iodine vapor. (A) FAME STD; (B) Fraction A (tube numbers: 1-10); (C) Fraction B (tube numbers: 11-16); (D) Fraction C (tube numbers: 17-24).

(47.5%) > solvent quantity (26.7%) > reaction time (17.5%) > amount of catalyst (8.3%). The maximum biodiesel yield of 55.07 ± 2.18% (based on lipid weight) was obtained under the following conditions: solvent quantity of 50 mL, NaOH amount of 0.5% (based on the lipid weight), a reaction time of 2hrs, and a reaction temperature of 60°C (P < 0.05). However, TLC analysis of the FAMEs showed that 48.41% of highly purified FAME was obtained through acidic catalysis, whereas 23.67% was obtained through alkaline catalysis, with less contamination by lipid pigments. It was also found that the quality of the biodiesel produced using the acidic catalyst was better than that produced using the alkaline catalyst by having higher amounts of C16:0 and C18:3. These results clearly indicated that an in situ transesterification process

using an acidic catalyst should have an excellent potential for directly producing biodiesel from microalgae [43]. However, the entire process should be further developed to meet the economic feasibility required to scale up to industrial production. Nonetheless, these results could provide information for economically producing biofuels from Scenedesmus sp. microalga based on the quantity and quality of the algal biodiesel produced in this study.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

# m * *

(A) (B) (C) (D)

• •

(A) (B) (C) (D)

(a) (b)

Figure 8: Thin layer chromatograms of the FAME fractions on HPTLC plates that were developed using n-hexane: ether (90 : 10, v/v) and visualized using (a) 10% phosphomolybdic acid in ethanol and in (b) iodine vapor. (A) FAME STD; (B) fraction A (tube numbers: 1-12); (C) fraction B (tube numbers: 13-23); (D) fraction C (tube numbers: 24-27).

Table 5: Comparison of fatty acids content in Scenedesmus sp. by in situ transesterification alkali and acid catalysis.

Catalyst C 14:0 C 16: 0 Fatty acids composition (%) C 18:3

C16: 1 C18:0 C18:1 C18:2

Acid 0.43 33.21 0.69 1.70 0.67 11.59 41.22

Alkali 0.52 30.11 0.99 1.84 0.41 10.51 37.98

Acknowledgment

This research was supported by a grant from Marine Biotechnology Program Funded by Ministry of Oceans and Fisheries,

Korea.

References

[1] D. Bajpai and V. K. Tyagi, "Biodiesel: source, production, composition, properties and its benefits," Journal ofOleo Science,vol 55, no. 10, pp. 487-502, 2009.

[2] X. Meng, J. Yang, X. Xu, L. Zhang, Q. Nie, and M. Xian, "Biodiesel production from oleaginous microorganisms," Renewable Energy, vol. 34, no. 1, pp. 1-5, 2009.

[3] Y. Chisti, "Biodiesel from microalgae," Biotechnology Advances, vol. 25, no. 3, pp. 294-306, 2007.

[4] L. Gouveia and A. C. Oliveira, "Microalgae as a raw material for biofuels production," Journal of Industrial Microbiology and Biotechnology, vol. 36, no. 2, pp. 269-274, 2009.

[5] X. Miao, P. Li, R. Li, and J. Zhong, "In situ biodiesel production from fast-growing and high oil content chlorella pyrenoidosa in rice straw hydrolysate," Journal of Biomedicine and Biotechnology, vol. 2011, Article ID 141207, 8 pages, 2011.

[6] H. P. S. Makkar and K. Becker, "Jatropha curcas, a promising crop for the generation of biodiesel and value-added coprod-ucts," European Journal of Lipid Science and Technology, vol. 111, no. 8, pp. 773-787, 2009.

[7] A. Richmond, "Microalgae of economic potential," in Handbook of Microalgal Mass Culture, pp. 199-243, Taylor & Francis, New York, NY, USA, 1986.

[8] A. L. Haag, "Algae bloom again," Nature, vol. 447, no. 7144, pp. 520-521, 2007.

[9] M. E. Huntley and D. G. Redalje, "CO2 mitigation and renewable oil from photosynthetic microbes: a new appraisal," Mitigation and Adaptation Strategies for Global Change, vol. 12, no. 4, pp. 573-608, 2007.

[10] O. Pulz and W. Gross, "Valuable products from biotechnology of microalgae," Applied Microbiology and Biotechnology, vol. 65, no. 6, pp. 635-648, 2004.

[11] R. Raja, S. Hemaiswarya, N. A. Kumar, S. Sridhar, and R. Rengasamy, "A perspective on the biotechnological potential of microalgae," Critical Reviews in Microbiology, vol. 34, no. 2, pp. 77-88, 2008.

[12] J. I. Park, H. C. Woo, and J. W. Lee, "Production of bio-energy from microalgae: status and perspectives," Korean Journal of Chemical Engineering, vol. 46, no. 5, pp. 833-844, 2008.

[13] T. Matsunaga, M. Matsumoto, Y. Maeda, H. Sugiyama, R. Sato, and T. Tanaka, "Characterization of marine microalga, Scenedesmus sp. strain JPCC GA0024 toward biofuel production," Biotechnology Letters, vol. 31, no. 9, pp. 1367-1372, 2009.

[14] N. Y. Kim, S. H. Oh, H. Y. Lee, and S. Y. Lee, "Extraction, purification and property of the lipid from Scenedesmus sp.," Korean Society for Biotechnology and Bioengineering Journal, vol. 25, no. 4, pp. 363-370, 2010.

[15] N. Y. Kim, S. H. Oh, H. Y. Lee, and S. Y. Lee, "Optimization of lipid extraction from Scenedesmus sp. using taguchi approach," Korean Society For Biotechnology and Bioengineering Journal, vol. 25, no. 4, pp. 371-378, 2010.

[16] A. S. Ramadhas, S. Jayaraj, and C. Muraleedharan, "Biodiesel production from high FFA rubber seed oil," Fuel, vol. 84, no. 4, pp. 335-340, 2005.

[17] K. G. Georgogianni, M. G. Kontominas, P. J. Pomonis, D. Avlonitis, and V. Gergis, "Conventional and in situ transester-ification of sunflower seed oil for the production of biodiesel," Fuel Processing Technology, vol. 89, no. 5, pp. 503-509, 2008.

[18] A. I. Carrapiso, L. M. Timon, J. M. Petron, J. F. Tejeda, and C. Garcia, "In situ transesterification of fatty acids from Iberian pig subcutaneous adipose tissue," Meat Science, vol. 56, no. 2, pp. 159-164, 2000.

[19] F. Sahena, I. S. M. Zaidul, S. Jinap et al., "Application of supercritical CO2 in lipid extraction—a review," Journal of Food Engineering, vol. 95, no. 2, pp. 240-253, 2009.

[20] J. Qian, F. Wang, S. Liu, and Z. Yun, "In situ alkaline transesterification of cottonseed oil for production of biodiesel and nontoxic cottonseed meal," Bioresource Technology, vol. 99, no. 18, pp. 9009-9012, 2008.

[21] M. B. Johnson and Z. Wen, "Production of biodiesel fuel from the microalga schizochytrium limacinum by direct transesterification of algal biomass," Energy and Fuels, vol. 23, no. 10, pp. 5179-5183, 2009.

[22] M.-Y. Chang, G.-J. Tsai, and J.-Y. Houng, "Optimization of the medium composition for the submerged culture of Ganoderma lucidum by Taguchi array design and steepest ascent method," Enzyme and Microbial Technology, vol. 38, no. 3-4, pp. 407-414, 2006.

[23] S. S. Mahapatra and A. Patnaik, "Optimization of wire electrical discharge machining (WEDM) process parameters using Taguchi method," International Journal of Advanced Manufacturing Technology, vol. 34, no. 9-10, pp. 911-925, 2007.

[24] S. V. Mohan, N. C. Rao, K. K. Prasad, P. M. Krishna, R. S. Rao, and P. N. Sarma, "Anaerobic treatment of complex chemical wastewater in a sequencing batch biofilm reactor: process optimization and evaluation offactor interactions using the taguchi dynamic DOE methodology," Biotechnology and Bioengineering, vol. 90, no. 6, pp. 732-745, 2005.

[25] E. A. Ehimen, Z. F. Sun, and C. G. Carrington, "Variables affecting the in situ transesterification of microalgae lipids," Fuel, vol. 89, no. 3, pp. 677-684, 2010.

[26] B. Liu and Z. Zhao, "Biodiesel production by direct methanol-ysis of oleaginous microbial biomass," Journal of Chemical Technology and Biotechnology, vol. 82, no. 8, pp. 775-780, 2007.

[27] H. T. Quach, R. L. Steeper, and G. W. Griffin, "An improved method for the extraction and thin-layer chromatography of chlorophyll a and b from spinach," Journal of Chemical Education, vol. 81, no. 3, pp. 385-387, 2004.

[28] B. A. McKittrick, S. Dugar, and D. ABurnett, "Sulfur-substituted azetidinone compounds useful as hypocholesterolemic agents," US patent no. 5774467,1998.

[29] Y. K. Lim, D. K. Kim, and E. S. Yim, "Synthesis of biodiesel from vegetable oil and their characteristics in low temperature," Journal of the Korean Industrial and Engineering Chemistry, vol. 20, no. 2, pp. 208-212, 2009.

[30] K. D. Muller, H. Husmann, H. P. Nalik, and G. Schomburg, "Trans-esterification of fatty acids from microorganisms and human blood serum bytrimethylsulfonium hydroxide (TMSH) for GC analysis," Chromatographia, vol. 30, no. 5-6, pp. 245-248, 1990.

[31] U. Schuchardt, R. Sercheli, and R. M. Vargas, "Transesterification of vegetable oils: a review," Journal oftheBrazilian Chemical Society, vol. 9, no. 3, pp. 199-210,1998.

[32] J. M. Encinar, J. F. González, J. J. Rodriguez, and A. Tejedor, "Biodiesel fuels from vegetable oils: transesterification of Cynara cardunculus L. Oils with ethanol," Energy and Fuels, vol. 16, no. 2, pp. 443-450, 2002.

[33] U. Rashid and F. Anwar, "Production of biodiesel through optimized alkaline-catalyzed transesterification ofrapeseed oil," Fuel, vol. 87, no. 3, pp. 265-273, 2008.

[34] M. K. Lam, K. T. Lee, and A. R. Mohamed, "Homogeneous, heterogeneous and enzymatic catalysis for transesterification of high free fatty acid oil (waste cooking oil) to biodiesel: a review," Biotechnology Advances, vol. 28, no. 4, pp. 500-518, 2010.

[35] S. Al-Zuhair, "Production of biodiesel: possibilities and challenges," Biofuels, Bioproducts and Biorefining, vol. 1, no. 1, pp. 57-66, 2007.

[36] O. O. Oluwaniyi and S. A. Ibiyemi, "Efficacy of catalysts in the batch esterification of the fatty acids of ThevetiaPeruviana seed oil," Journal of Applied Sciences and Environmental Management, vol. 7, no. 1, pp. 15-17, 2003.

[37] X. Fan, Optimization ofBiodiesel Productionfrom Crude Cottonseed Oil and Waste Vegetable Oil: Conventional and Ultrasonic Irradiation Methods, Clemson University, Clemson, SC, USA, 2008.

[38] G. Taguchi, Introduction to Quality Engineering: Designing Quality into Products and Processes, 1986.

[39] L. C. Meher, D. Vidya Sagar, and S. N. Naik, "Technical aspects of biodiesel production by transesterification—a review," Renewable and Sustainable Energy Reviews, vol. 10, no. 3, pp. 248-268, 2006.

[40] N. Dizge, C. Aydiner, D. Y. Imer, M. Bayramoglu, A. Tanriseven, and B. Keskinler, "Biodiesel production from sunflower, soybean, and waste cooking oils by transesterification using lipase immobilized onto a novel microporous polymer," Bioresource Technology, vol. 100, no. 6, pp. 1983-1991, 2009.

[41] R. Xu and Y. Mi, "Simplifying the process of microalgal biodiesel production through in situ transesterification technology," Journal oftheAmerican Oil Chemists' Society, vol. 88, no. 1,pp. 91-99, 2011.

[42] B. D. Wahlen, R. M. Willis, and L. C. Seefeldt, "Biodiesel production by simultaneous extraction and conversion of total lipids from microalgae, cyanobacteria, and wild mixed-cultures," Bioresource Technology, vol. 102, no. 3, pp. 2724-2730, 2011.

[43] A. P. Vyas, J. L. Verma, and N. Subrahmanyam, "A review on FAME production processes," Fuel, vol. 89, no. 1, pp. 1-9, 2010.

Copyright of BioMed Research International is the property of Hindawi Publishing Corporation and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use.