Scholarly article on topic 'Live-cell multiplane three-dimensional super-resolution optical fluctuation imaging'

Live-cell multiplane three-dimensional super-resolution optical fluctuation imaging Academic research paper on "Chemical sciences"

CC BY-NC-SA
0
0
Share paper
Academic journal
Nature Communications
OECD Field of science
Keywords
{""}

Academic research paper on topic "Live-cell multiplane three-dimensional super-resolution optical fluctuation imaging"

COMMUNICATIONS

ARTICLE

Received 27 Aug 2014 | Accepted 12 Nov 2014 | Published 18 Dec 2014^^BoOl:iaio38/ncomms683o| OPEN

Live-cell multiplane three-dimensional super-resolution optical fluctuation imaging

Stefan Geissbuehler1, Azat Sharipov1, Aurelien Godinat2, Noelia L. Bocchio1, Patrick A. Sandoz3,

Anja Huss4, Nickels A. Jensen5, Stefan Jakobs5, Jörg Enderlein4, F. Gisou van der Goot3, Elena A. Dubikovskaya2,

Theo Lasser1 & Marcel Leutenegger1

Super-resolution optical fluctuation imaging (SOFI) provides an elegant way of overcoming the diffraction limit in all three spatial dimensions by computing higher-order cumulants of image sequences of blinking fluorophores acquired with a classical widefield microscope. Previously, three-dimensional (3D) SOFI has been demonstrated by sequential imaging of multiple depth positions. Here we introduce a multiplexed imaging scheme for the simultaneous acquisition of multiple focal planes. Using 3D cross-cumulants, we show that the depth sampling can be increased. The simultaneous acquisition of multiple focal planes significantly reduces the acquisition time and thus the photobleaching. We demonstrate multiplane 3D SOFI by imaging fluorescently labelled cells over an imaged volume of up to 65 x 65 x 3.5 mm3 without depth scanning. In particular, we image the 3D network of mitochondria in fixed C2C12 cells immunostained with Alexa 647 fluorophores and the 3D vimentin structure in living Hela cells expressing the fluorescent protein Dreiklang.

1 École Polytechnique Fédérale de Lausanne, Laboratoire d'Optique Biomédicale, 1015 Lausanne, Switzerland. 2 École Polytechnique Fédérale de Lausanne,

Laboratory of Bioorganic Chemistry and Molecular Imaging, Institute of Chemical Sciences and Engineering (ISIC), 1015 Lausanne, Switzerland. 3 École

Polytechnique Féderale de Lausanne, Global Health Institute, 1015 Lausanne, Switzerland. 4Georg August University, III. Institute of Physics, 37077 Gottingen,

Germany. 5 Max Planck Institute for Biophysical Chemistry, Department of NanoBiophotonics, 37077 Gottingen, Germany. Correspondence and requests for

materials should be addressed to S.G. (email: stefan.geissbuehler@alumni.epfl.ch).

A microscope is characterized by its three-dimensional (3D) point spread function (PSF) whose spatial extents determine the resolution in the corresponding spatial dimensions. The image of a single fluorescent molecule essentially corresponds to the PSF centred on the position of the molecule. By sequentially imaging isolated fluorophores, determining their PSF centres and mapping them into a position histogram, localization microscopy can render the sample structure with much finer details than classical fluorescence microscopes1-5. However, this requires the use of fluorophores that can be photo-switched or -activated stochastically. The characteristic rates of activation and deactivation need to be tuned such that only a sparse subset of molecules is active per exposure and a sufficiently high number of photons can be detected for a precise localization6-8. As an alternative to single-molecule localization, super-resolution optical fluctuation imaging (SOFI) achieves super-resolution using higher-order statistics with relaxed requirements on the photo-switching kinetics9'10. SOFI relies on reversible stochastic and independent intensity fluctuations from fluorophores but tolerates a spatio-temporal overlap of their images, incomplete on-off-switching and moderate visibility of the intensity fluctuations. The method has been successfully demonstrated with semiconductor quantum dots9,11, organic dyes12 and fluorescent proteins13. With the help of time-correlated single photon counting instrumentation, the stochastic photon emission from single fluorophores and the associated antibunching effect was exploited in combination with a modified SOFI analysis14. Recently, SOFI was applied to fluorescence fluctuations induced by stochastic approaches of fluorescence resonance energy transfer pairs15, where the energy transfer donor was linked to the structure of interest and the acceptor diffusing in the medium.

So far, 3D SOFI has only been demonstrated by stacking sequentially acquired optical sections13,16. In this paper, we introduce an imaging scheme for the simultaneous acquisition of multiple focal planes. The SOFI analysis can then be performed in 3D to increase the spatial sampling and to improve the resolution in all dimensions. In comparison to the sequential imaging of several depth planes, a parallel multiplane acquisition with a numerically increased depth sampling can significantly reduce the acquisition time and therewith limit the photobleaching of markers. We demonstrate the performance of this approach by imaging mitochondria in fixed cells and the vimentin network in living cells.

Results

Multiplane 3D SOFI. The most basic implementation of SOFI corresponds to the calculation of the temporal variance of an image sequence of stochastically fluctuating emitters. Owing to the independence of the fluctuations, the signals from different emitters are uncorrelated. In consequence, the variance of the total signal from N emitters is the sum of the variances of every single-emitter signal If

Î>(r't) =E var{ii(r' *)}>

where i is the index of the emitter, r denotes a pixel location on the detector and t is the time. The signal from a single emitter located at ri corresponds to a sampled and shifted version of the microscope's PSF U(r — ri) with a brightness amplitude ei times a fluctuation signal si(t) that encodes the temporal fluctuations. The single-emitter variance then reads

var{/;(r, t)} = e2U2(r - r;)var{s;(f)}.

Obviously, the variance-equivalent PSF is given by the original PSF raised to the power of two. This doubles the spatial frequency support of the corresponding optical transfer function and increases the spatial resolution.

Instead of calculating the temporal variance on each pixel separately, the covariance of neighbouring pixels provides an additional advantage as it cancels any uncorrelated noise. Furthermore, by using different combinations of pixel pairs for calculating the covariance, the final image sampling can be increased as the covariance essentially probes the sample in the geometrical mean of the chosen pixel pair (Fig. 1).

Multiplying the PSF with itself for improving the resolution as in the variance and covariance can be generalized to higher orders using cumulants or cross-cumulants9,11. The second-order cumulant without time lag is equivalent to the variance and the second-order cross-cumulant corresponds to the covariance. An n-th order cumulant or cross-cumulant raises the PSF to the power of n. Cumulants thus provide a mean for resolution enhancement that is ultimately limited by the signal-to-noise ratio (SNR) only. As shown by Dertinger et al.11, cross-cumulants among a group of pixel time traces allow to eliminate any noise bias and to increase the pixel grid density, such that the cumulant image resolution is not limited by the effective pixel size. This results in a 3D image with up to n3 times the original number of pixels for a cumulant order n. Figure 1 illustrates the calculation of cross-cumulants up to the fourth order for pixels {rA,rB,rC,rD} that may differ in any spatial direction including the so far unexploited axial dimension. To maximize the speed and the field-of-view, each dimension of the PSF is oversampled just enough to satisfy Shannon's sampling theorem17 and to ensure a correlated signal between the cross-cumulated pixels. For a given spatial sampling distance, the more pixels that are acquired and read simultaneously, the faster the overall image acquisition becomes. It is thus advantageous to use a widefield imaging system with a high pixel-count camera that is sufficiently sensitive and rapid to detect the emitters' fluorescence fluctuations.

In order to fully exploit the resolving power of higher-order cross-cumulants with a balanced image contrast, we applied a simplified linearization18. The absolute value of the resulting cumulant image is first deconvolved in 3D using a Lucy-Richardson algorithm. The log-likelihood formulation used in the algorithm is well adapted for cumulants as long as there are no

Pixel group nth order cross-cumulant computation A B C "d

n Partitions

"xj r = - £ r,;t ) = E ("1)|P| - 1(IPI - 1)1 n (iPi

\ i=1 I P . _____. peP Vep

x = {yB,/c,...}

Output # Parts Partition Partition products X - {,A''B''C" position IP | prefactor___'A - /(rA,t - ta)

2 ' ' ... i 2 i -i (Ia Ib) <Ia> (Ib)

3 : ■ : ■ : i 2 3 i -i 2 (Ia Ib Ic) (M (Ib IC) ,{IB) {IA IC) ,<Ic> (Ia Ib) «a) (Ib) (Ic)

<(a Ib IcID)

(/a IB) </cID) A/A IC) (IB b) ,(/a D (IB C , ((a) (Ib Ic Id) ,<Ib> (Ia Ic Id) , -<M (Ib IC) {ID) ,{IB) (Ia Id) {IC) ,... {(A) {IB) {IC)(Id)

Figure 1 | Calculation of cross-cumulants. The cross-cumulant kx,„ of order n for a pixel group S = {rA, rB, rC, rD} can be calculated as a sum over all partitions of S. Each addend consists of a prefactor depending on the number of parts |P| in the particular partition P times a partition product, which evaluates the parts p as a temporally averaged (...) product. White, red, blue and yellow backgrounds indicate parts of a partition comprising, respectively, one to four pixels.

sign changes within a PSF. We then take the n-th root and reconvolve the image with an «-times size-reduced PSF to limit the apparent final resolution to a physically reasonable value given by the support of the cumulant optical transfer function.

Figure 2a outlines a widefield setup for the simultaneous acquisition of multiple focal planes with two cameras. The use of an index-matched immersion objective lens (for example, a water-immersion objective if the sample is in an aqueous environment) minimizes spherical aberrations when imaging thick samples. Three diagonally arranged 50:50 beam splitters behind the lens f2 split the collected fluorescence into eight separate detection channels. Four mirrors are adjusted to direct the light onto separate areas of the two cameras. By axially shifting two mirrors by a distance d and 2d as indicated in Fig. 2a and by shifting one camera by a distance 4d, eight different optical path lengths are achieved with respect to the lens f2. Therefore, eight distinct and conjugated depth positions are probed in the sample. The focal plane separation in the object space is then approximately given by d/Ma, where Ma is the axial magnification (square of the lateral magnification). To comply

with Shannon's sampling theorem, this distance should not exceed half the axial resolution of the imaging system. The field stop has an adjustable rectangular shape and is used to avoid crosstalk between the detection channels. By adding or removing a pair of mirrors and a beam splitter, the number of detection channels can be increased or decreased.

Mitochondria in immunostained fixed cells. In view of imaging a deep red emitting organic fluorophore, Alexa 647, we adjusted the distances between the focal planes in the sample to 500 nm (Fig. 2c,d). Using a fluorescent bead sample (Fig. 2b), we determined the transverse positioning and the mutual distortion of the detection channels for co-registration and measured the full-width-at-half maxima of the PSF in the transverse (320 nm) and axial dimension (1.2 mm). The mutual distortions include the effects of small differences in lateral magnifications and distortions because of non-telecentric and tilted image formation on the camera sensors as well as different wavefront aberrations by the optical elements of the image splitter.

Detection channel

Figure 2 | Simultaneous detection of multiple focal planes. (a) Multiplane widefield fluorescence microscope. The excitation laser is focused into the aperture of the objective to create a large illumination field. Sample features in several focal planes are imaged simultaneously by two cameras. These focal planes are obtained by splitting the fluorescence into several channels using three 50:50 beam splitter cubes and by introducing path length differences d and 2d with the mirrors, as well as 4d with camera 1 (the grey-shaded element positions would result in a single focal plane detection). The resulting separation between the focal planes in the object space is then approximately d/Ma, with Ma being the axial magnification of the system. The images of the focal planes are projected side-by-side on the cameras. A field stop in the intermediate image prevents overlaps between the image frames. (b) Image frames taken with a fluorescent bead sample. (c) Peak brightness in the image frames in b upon scanning the sample plane through the focal channels. (d) Calibration of the focal plane separation by the positions of the brightness maxima in c.

We labelled mitochondria by decorating fixed C2C12 cells with antiserum against Tom20, an abundant protein of the outer membrane, and a secondary antibody coupled to Alexa 647. At the imaging conditions, Alexa 647 showed pronounced blinking with an average on time of about 20 ms and an estimated off time of 1-2 s. Taking 5,000 images acquired at 40 frames per second (f.p.s.), we obtained 3D super-resolved images of mitochondria as shown in Fig. 3 and Supplementary Movie 1. The simultaneous acquisition of multiple focal planes allowed a volume of 65 x 65 x 3.5 mm3 to be imaged without scanning. We computed third-order cross-cumulants in order to increase the sampling density threefold in all spatial dimensions. Instead of the original 8 sampling points along the optical axis (Fig. 3g), we therefore obtained 22 points, which significantly improves the visibility of structural details in depth (Fig. 3d-f). The third-order balanced cumulant image18 clearly reveals spherical and tubular mitochondrial features (Fig. 3a,b and d-f), whereas in the diffraction-limited image those features are barely visible (Fig. 3c,g). The strong out-of-focus background is almost completely removed in the 3D SOFI image. As shown in the profiles in Fig. 3h,i, the smallest features resolved in transverse and meridional sections of the image indicate a lateral resolution of about 110 nm and an axial resolution better than 500 nm, which approaches the expected threefold increase in 3D resolution.

For further comparison, Supplementary Fig. 3 shows the second-order SOFI image without deconvolution and linearization, where we chose a partially saturated image representation to accommodate for the high image contrast. Residual artefacts of the sub-pixel grid are visible around defocused features. Because second-order SOFffiIffi improves the resolution only by a factor of approximately \¡2 (ref. 9), third-order balanced SOFI resolves small features significantly better as exemplified by Fig. 3b,h and Supplementary Fig. 3.

Vimentin-Dreiklang-transfected living cells. To demonstrate live-cell imaging with short acquisition times, we imaged the

vimentin network in living HeLa cells using the reversibly switchable fluorescent protein Dreiklang19 (cf. Figs 4 and 5). Dreiklang possesses three separate but partly overlapping absorption spectra for exciting fluorescence and switching it on and off. This allows for a flexible tuning of photo-switching kinetics and number of photons per switching cycle. We used 405 nm light, which excites in the overlapping absorption bands for switching on and off, to switch Dreiklang at a low on-ratio of about 1%. We used 532 nm light to excite fluorescence well above the absorption maximum in order to avoid switching Dreiklang off at the same time. The distances between the focal planes were then adjusted to 400 nm to account for the shorter wavelength and the resulting reduction in PSF size. The total depth range covered with the eight planes was reduced to 2.8 mm, which was usually too short to cover an entire vimentin network (Fig. 4a,b). By increasing the 405 nm illumination intensity, the switching rate of Dreiklang can be increased. We adapted the frame rate so that the exposure time corresponded approximately to the characteristic on-time and changed the fluorescence excitation proportionally in order to determine the maximum acquisition speed yielding a good image quality. With illumination intensities of about 100 W cm " 2 at 405 nm and 3kWcm " 2 at 532 nm, the acquisition of about 1,000 frames at 325 f.p.s. was sufficient for a decent SNR in a second-order cross-cumulants analysis (Fig. 4e,f). As the total number of emitted photons per fluorophore usually lowers with increasing switching speeds, it is rather preferable to reduce the illumination intensities and accordingly the acquisition speed while keeping motion artefacts small. For Fig. 5, we reduced the number of planes to four and additionally moved the sample along the axis to cover a total depth of 4 mm in three sequential acquisitions. For a twofold 3D resolution improvement, we evaluated 3,000 images taken at 50 f.p.s. with accordingly reduced illumination intensities of 15Wcm" 2 at 405 nm and 450 W cm " 2 at 532 nm.

rx z "I

z (|m)

Figure 3 | Mitochondria stained with Alexa 647 in fixed C2C12 cells. (a) Maximum intensity projection of the third-order balanced SOFI image covering a volume of 65 x 65 x 3.5 mm3. (b) Zoomed region highlighted in a. (c) Diffraction-limited widefield view of the same area as b. (d-f) x-z Sections highlighted in a averaged over 25 pixels along y. (g) Same x-z section as f from diffraction-limited widefield stack. (h) x-Profiles from the cut 1-10 highlighted in b. (i) z-Profile from the cut 2-20 highlighted in e. Scale bars: (a) 5 mm (b,c) 2 mm (d-g) 1 mm in x and z.

Figure 4 | Live-cell multiplane SOFI of HeLa cells expressing vimentin-Dreiklang optimized for acquisition speed. Acquisition rates and number of frames: (a,b) 50f.p.s., 3,000 frames; (c,d) 325f.p.s., 3,000 frames; (e-g) 325f.p.s., 1,500, 500 and 200 frames. (a,c) Maximum intensity projection of 8-plane widefield images. (b,d-g) Maximum intensity projection of second-order balanced SOFI. The original eight axial sampling points are complemented by virtual pixels using a 3D second-order cross-cumulant analysis to yield a total of 15. (e-g) Zoomed region highlighted in c showing the resulting second-order balanced SOFI image obtained from 1,500 (4.6 s), 500 (1.5 s) and 200 (0.6 s) frames, respectively, and having the same central time point. For a decent SNR, at least 500 frames seem to be needed. Scale bars: (a,b) 5mm (c,d) 2 mm (e-g) 1 mm.

Figure 5 | Live-cell multiplane SOFI of HeLa cells expressing vimentin-Dreiklang. (a) Maximum intensity projection of widefield images. (b) Maximum intensity projection of second-order balanced SOFI. (c) Zoomed region highlighted in b. (d-f) x-z Sections highlighted in b. Scale bars: (a,b) 5 mm (c) 1 mm (d-f) 1 mm in x and z.

Discussion

For widefield 3D SOFI, it is favourable to acquire multiple depth planes simultaneously. The optimal number of detection channels is limited by the detectable fluctuation signal from the fluorophore and the sensitivity of the detection system. As a guideline, the detected fluctuation amplitude in each channel should at least exceed the read noise amplitude. Using a cross-cumulants analysis of stochastically blinking fluorescent emitters across the individual depth planes, the physically acquired depth planes are supplemented by virtual planes providing a finer depth sampling. As a result, the axial PSF needs not to be n times oversampled as would be the case for axially scanned n-th order 3D SOFI. Accordingly, multiple simultaneously acquired focal planes in combination with 3D cross-cumulants allow for a reduction in the acquisition time and a better exploitation of the

available photon budget from the fluorescent markers, particularly if the emitters are prone to bleaching.

The resulting contrast of the 3D cross-cumulants is more homogeneous along the optical axis when compared with sequential plane-by-plane 2D cross-cumulants. During sequentially acquired depth sections, the cumulant response of individual emitters might change because of stochasticity resulting in a potentially imbalanced cumulant contrast, which would be problematic for subsequent 3D deconvolution and cumulant balancing (as described in ref. 18). As cross-cumulants cancel uncorrelated noise, the image quality is greatly improved. However, auto-fluorescence and/or strongly defocused fluorophores can contribute correlated noise upon photo-bleaching. Therefore, we minimize photobleaching at best and adjust the sequence length for the data analysis. Some cameras

showed correlated read noise, which we attribute to clocking noise upon charge shifting (EMCCD) or row switching (CMOS) at high speed. Therefore, the cameras have been carefully selected for minimizing this correlating bias.

The present implementation of a multiplane fluorescence microscope is versatile but susceptible to misalignment of the detection channels because of drift of the components. An integrated image splitter with a minimal number of elements would simplify the alignment and improve the stability. Instead of refractive elements, it is also possible to use a specifically designed 2D grating in combination with glass prisms to generate several depth planes on a single camera20. With a wavefront-corrected grating, this concept would enable the use of high-numerical aperture oil-immersion objectives by compensating the spherical aberrations arising from refractive index mismatches.

In principle, the resolution in live cells densely stained with Dreiklang could be further improved if the on-time ratio could be lowered, for instance by shifting the switching light to a slightly longer wavelength and thus substantially reduce the on-switching. Alternatively, the fluorescence excitation wavelength could be blue-shifted in order to increase the off-switching while keeping the same on-switching rate. Whereas SOFI can handle multiple markers emitting simultaneously, it is nevertheless beneficial to keep this number reasonably low for improving the visibility of the blinking events.

In addition to the improved structural information, SOFI may also provide functional information via a cumulants analysis with different time lags. This enables the quantification of signal fluctuations at different time scales, such as the switching kinetics of the fluorophores and also sample movements. Furthermore, combining the information from several cumulant orders allows to extract spatially resolved molecular state lifetimes, concentrations and fluorescence amplitudes, which may be linked to the surrounding microenvironment18.

In summary, we introduced a fast and versatile multiplane 3D SOFI concept allowing super-resolved cell imaging in 3D without scanning. We imaged the outer membrane of mitochondria in C2C12 cells as well as the vimentin network of living HeLa cells using an eight-plane detection scheme. Compared with the diffraction-limited image, we demonstrated an up to threefold resolution improvement in all three dimensions in fixed cells and a twofold 3D resolution improvement at acquisition times of a few seconds in living cells.

Methods

Microscope setup. The custom-built microscope system (Fig. 2a) comprised a 1.2 numerical aperture x 60 water-immersion objective (UPLSAPO 60XW, Olympus), two diode lasers for excitation and reactivation (MLL-III-635, 800 mW, Roithner Lasertechnik, and iBeam smart, 405 120 mW, Toptica) as well as a green DPSS laser (MLL-FN-532 800 mW, Roithner Lasertechnik), a multiplane splitter with three 50:50 beam splitters (BS013, Thorlabs) and two sCMOS cameras (ORCA Flash 4.0, Hamamatsu). For Alexa 647 imaging, the illumination intensities were adjusted to 2 kW cm _ 2 at 635 nm (excitation) and 20 W cm _ 2 at 405 nm (faster reactivation). Dreiklang was switched with 15 W cm _ 2 at 405 nm and excited with 450 W cm _ 2 at 532 nm. Dreiklang switching kinetics were measured with the same setup, but with reduced illumination intensities (5.6 W cm _ 2 at 405 nm, 0.7 W cm _ 2 at 532 nm) and an additional 365 nm LED epi-illumination with 1.6 W cm _ 2 (switching on).

Data analysis. A detailed description of the multiplane SOFI analysis may be found in Supplementary Note 1 with a flowchart given in Supplementary Fig. 1. In brief, each registered pair of image sequences from consecutive depth channels was divided into 500-frame (Alexa 647) or 100-frame (Dreiklang) sub-sequences and processed with a 3D cross-cumulants analysis using voxel combinations without repetitions (Supplementary Fig. 2) and zero time delays. The frames of one depth sequence were analysed without preprocessing, whereas the frames of the other sequence were co-registered using an affine transformation and bilinear interpolation. The transformation parameters were obtained from a calibration measurement using fluorescent beads. A subsequent fine-tuning of the image registration using a rigid transformation on the measurement data was necessary to

correct for residual mechanical drift of the detection optics. From each bi-plane cross-cumulants analysis, only virtual planes and the untransformed physical plane were kept for further processing, because the transformed depth plane contains correlated noise parts in neighbouring pixels introduced by the interpolation. The heterogeneous pixel weights—arising from different responses in the detection channels as well as the the different pixel groups used in the cross-cumulants— were corrected by dividing their respective standard deviations throughout the entire image. Compared with the original SOFI algorithms11,18 suggesting a distance-factor correction by fitting a PSF model that maximizes the image smoothness, this standard-deviation equalization has the advantage of being easier, faster and it seemed more robust with low SNRs, and the different detection responses are automatically corrected.

Subsequently, the bi-plane cumulant image blocks are transformed using the previously determined transformation masks in order to have all planes aligned. Finally, the nonlinear response of the cumulant with respect to differences in molecular brightness and blinking was linearized by using a 3D Lucy-Richardson deconvolution, taking the n-th root and reconvolving with an n-times size-reduced PSF. For the display of the z coordinate, we used an 'isolum' colourmap compatible with red-green colour perception deficiencies21.

Cell cultures. C2C12 cells were cultured at 37 0C with 5% CO2 using DMEM high glucose (4.5 gl_ 1 of glucose), containing 10% fetal bovine serum, 2% HEPES 1 M, 1% MEM Non-Essential Amino Acids Solution (100 x ) and 40 mgml_ 1 of Gentamycin (all products were purchased from Life Technologies Corporation). Cells were plated in 35 mm Fluorodish Cell Culture Dish (World Precision Instruments) at roughly 50,000 cells per plate on the day before fixation.

HeLa cells were cultured at 37 0C with 5% CO2 using Minimum Essential Medium Eagle with Earle's salts, L-glutamine, sodium bicarbonate complemented with 10% fetal bovine serum, 1 x penicillin-streptomycin, 1 x GlutaMAX, 1 x MEM Non-Essential Amino Acids Solution (all products were purchased from Life Technologies). Cells were plated in 4-well Nunc Lab-Tek II Chambered Coverglass (Thermo Fisher Scientific).

Immunostaining. C2C12 cells were washed three times carefully with PBS and were then incubated for 10min at room temperature (RT) in 10% neutral buffered formalin solution (4% (w/v) formaldehyde, Sigma-Aldrich) for fixation, followed by washing three times 5 min with PBS. The cells were then incubated for 60 min in TBS containg 0.1% Tween-20 (TBST) with 10% fetal calf serum (FCS) at RT, followed by incubation overnight at 4 0C with a primary antibody for Tom20 (mouse monoclonal, Abcam, ab56783) diluted 1:100 in TBST with 10% FCS. Cells were then washed three times for 5 min with PBS and incubated again at RT for 1-2h with a secondary antibody (donkey anti-mouse, Alexa Fluo 647), diluted 1:150 in TBST with 10% FCS. After washing the cells three times for 5 min with PBS, a postfixation was performed for 10 min with formalin solution at RT. Before addition of a 1:1 PBS/Glycerol solution, the cells were finally washed again three times for 5 min with PBS.

Imaging buffer. The Alexa 647 samples were imaged using a buffer containing an oxygen scavenger and a thiol. The solutions were prepared using PBS (Sigma-Aldrich), 0.5mgml_ 1 glucose oxidase (Sigma-Aldrich), 40 mgml_ 1 catalase (Sigma-Aldrich), 6.6% (w/v) glucose and 10 mM cysteamine (Sigma-Aldrich).

Transfection with vimentin-Dreiklang. HeLa cells were transfected using FuGENE 6 transfection reagent (Promega). For each 1.5 cm2 well, 2 ml Fugene were incubated in 33 ml OptiMEM Reduced-Serum Medium (Life Technologies) during 5 min before the addition of 0.67 mg of the plasmid pMD-Vim-Dreiklang19. The solution then stayed 30 min at RT before it was carefully distributed over the cells. Cells were then put back into the incubator and were left overnight before imaging.

Determination of Dreiklang switching kinetics. In order to determine the appropriate illumination intensities for SOFI measurements, we first determined the switching kinetics of Dreiklang from ensemble experiments with transfected HeLa cells. We implemented an additional 365 nm LED illumination (M365L2 from Thorlabs) to characterize both on- and off-switching of Dreiklang. We used the parallel port as a digital 8-port output to control illumination pulsing and camera synchronization via a Matlab Mex-File22. All the switching experiments were carried out on the presented setup using a widefield detection and illumination sources at 365, 405 and 532nm with 1.6, 5.6 and 0.7Wcm_2, respectively. A first experiment consisted in a repeated sequence of pulses of 532-405-532-365 nm light to characterize the on-switching ratios of both 405 and 365 nm illuminations (Supplementary Fig. 4a,b). The signal plotted in Supplementary Fig. 4a,b corresponds to the background-corrected fluorescence response from a cell transfected with Dreiklang averaged over a thresholded image. The population ratios P36s/Ptot and P4os/Ptot (corrected for bleaching) correspond

to the estimated on-ratios of 365 and 405 nm light:

ton;365 kon,365

pon ;365 :

ton ,365 + toff ,365 koff ,365 """ kon ,365

Pon ,405 :

t on ,405

ton ,405 + toff ,405 koff ,405 """ kon ,405

The second experiment summarized in Supplementary Fig. 4c,d consisted of a pulsed 365 nm and continuous 405 and 532 nm illumination for extracting the absolute kinetics. The average switch-on and switch-off curves are represented in Supplementary Fig. 4d with the fitted characteristic lifetimes ton = 1/koff,405 and toff = 1/(kon,365 + kon,405). The individual on- and off-switching lifetimes for 365 and 405 nm light at the given intensities can then be estimated as

ton ,405 = ton = 104 [ms]

toff,405 = ton,405 (l/Pon,405 ~ l) = 10[s] ton,365 = toff ,365 ^3

pon,365

= 383 [ms].

References

1. Rust, M, Bates, M. & Zhuang, X. Sub-diffraction-limit imaging by stochastic optical reconstruction microscopy (STORM). Nat. Methods 3, 793-795 (2006).

2. Betzig, E. et al. Imaging intracellular fluorescent proteins at nanometer resolution. Science 313, 1642-1645 (2006).

3. Hess, S, Girirajan, T. & Mason, M. Ultra-high resolution imaging by fluorescence photoactivation localization microscopy. Biophys. J. 91, 4258-4272 (2006).

4. Folling, J. et al. Fluorescence nanoscopy by ground-state depletion and single-molecule return. Nat. Methods 5, 943-945 (2008).

5. Heilemann, M. et al. Subdiffraction-resolution fluorescence imaging with conventional fluorescent probes. Angew. Chem. Intl Ed. 47, 6172-6176 (2008).

6. van de Linde, S, Wolter, S, Heilemann, M. & Sauer, M. The effect of photoswitching kinetics and labeling densities on super-resolution fluorescence imaging. J. Biotechnol. 149, 260-266 (2010).

7. Zhu, L, Zhang, W, Elnatan, D. & Huang, B. Faster STORM using compressed sensing. Nat. Methods 9, 721-723 (2012).

8. Babcock, H, Sigal, Y. M. & Zhuang, X. A high-density 3D localization algorithm for stochastic optical reconstruction microscopy. Opt. Nanoscopy 1, 6 (2012).

9. Dertinger, T, Colyer, R, Iyer, G, Weiss, S. & Enderlein, J. Fast, background-free, 3D super-resolution optical fluctuation imaging (SOFI). Proc. Natl Acad. Sci. USA 106, 22287-22292 (2009).

10. Geissbuehler, S, Dellagiacoma, C. & Lasser, T. Comparison between SOFI and STORM. Biomed. Opt. Express 2, 408-420 (2011).

11. Derringer, T, Colyer, R, Vogel, R, Enderlein, J. & Weiss, S. Achieving increased resolution and more pixels with superresolution optical fluctuation imaging (SOFI). Opt. Express 18, 18875-18885 (2010).

12. Dertinger, T, Heilemann, M, Vogel, R, Sauer, M. & Weiss, S. Superresolution optical fluctuation imaging with organic dyes. Angew. Chem. Intl Ed. 49, 9441-9443 (2010).

13. Dedecker, P, Mo, G. C. H, Dertinger, T. & Zhang, J. Widely accessible method for superresolution fluorescence imaging of living systems. Proc. Natl Acad. Sci. USA 109, 10909-10914 (2012).

14. Schwartz, O. & Oron, D. Improved resolution in fluorescence microscopy using quantum correlations. Phys. Rev. A 85, 033812 (2012).

15. Cho, S. et al. Simple super-resolution live-cell imaging based on diffusionassisted Forster resonance energy transfer. Sci. Rep. 3, 1208 (2013).

16. Derringer, T, Xu, J, Nairn, O, Vogel, R. & Weiss, S. SOFI-based 3D superresolution sectioning with a widefield microscope. Opt. Nanoscopy 1, 2 (2012).

17. Shannon, C. E. Communication in the presence of noise. Proc. IEEE 86, 447-457 (1998).

18. Geissbuehler, S. et al. Mapping molecular statistics with balanced superresolution optical fluctuation imaging (bSOFI). Opt. Nanoscopy 1, 4 (2012).

19. Brakemann, T. et al. A reversibly photoswitchable GFP-like protein with fluorescence excitation decoupled from switching. Nat. Biotechnol. 29, 942-947 (2011).

20. Abrahamsson, S. et al. Fast multicolor 3D imaging using aberration-corrected multifocus microscopy. Nat. Methods 10, 60-63 (2012).

21. Geissbuehler, M. & Lasser, T. How to display data by color schemes compatible with red-green color perception deficiencies. Opt. Express 21, 9862-9874 (2013).

22. Schieber, F. Mex-File Plug-in for Fast MATLAB Port I/O (64-bit Windows XP, Vista, 7). http://apps.usd.edu/coglab/psyc770/IO64.html (2010).

Acknowledgements

We thank Professor Johan Auwerx for kindly providing the C2C12 cells, Dr Erica Martin-Williams for proof-reading the manuscript, Professor Gabriel Popescu and Dr Claudio Dellagiacoma for helpful comments and discussions and Gennady Nikitin for his assistance with cell labelling. This research was supported by the Swiss National Science Foundation (SNSF) under grants CRSII3-125463/1 and 205321-138305/1. A.G. and E.A.D. acknowledge the grants from Neva Foundation. J.E. and S.J. greatfully acknowledge financial support by the Deutsche Forschungsgemeinschaft through SFB 755 (projects A5 and B10) and the Cluster of Excellence Nanoscale Microscopy and Molecular Physiology of the Brain (S.J.), and A.H. greatfully acknowledges financial support by the German Bundesministerium fur Bildung und Forschung (BMBF) via the Bernstein Center for Computational Neuroscience (BCCN, project A2, FKZ 01GQ1005A), Gottingen.

Author contributions

S.G., T.L. and M.L. conceived the study. S.G. and M.L. developed the algorithm. S.G., A.S., A.G., N.L.B., P.A.S., A.H. and N.A.J. prepared the samples. S.G. and A.S. performed the experiments and analyzed data. S.G. and M.L. wrote the manuscript and all authors commented on it at every stage.

Additional information

Supplementary Information accompanies this paper at http://www.nature.com/ naturecommunications

Competing financial interests: The authors declare no competing financial interests.

Reprints and permission information is available online at http://npg.nature.com/ reprintsandpermissions/

How to cite this article: Geissbuehler, S. et al. Live-cell multiplane three-dimensional super-resolution optical fluctuation imaging. Nat. Commun. 5:5830 doi: 10.1038/ ncomms6830 (2014).

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. The images or other third party material in this article are included in the article's Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http:// creativecommons.org/licenses/by-nc-sa/4.0/

on,405

toff ,365 = ¿ff = 160[ms]