Materials engineering topic list of research papers
-
Breathing walls: The design of porous materials for heat exchange and decentralized ventilation
Abstract This study demonstrates how to design pores in building materials so that incoming fresh air can be efficiently tempered with low-grade heat while conduction losses are kept to a minimum. Any base material can be used in principle, so long...
2017 / Salmaan Craig, Jonathan Grinham -
Simulation of Intelligent Single Wheel Mobile Robot2012 / Maki K. Rashid
-
Vibration Analysis of a Tire in Ground Contact under Varied Conditions2017 / Murat Karakus, Aydin Cavus, Mehmet Colakoglu
-
On nanostructured molybdenum–copper composites produced by high-pressure torsion2017 / Julian M. Rosalie, Jinming Guo, Reinhard Pippan, Zaoli Zhang
-
Printed H -plane horn antenna with loaded dielectric-metal composite lens2016 / Hua Zong, Xi Liu, Xinru Ma, Zhihua Zhao, Shu Lin
-
Atomic structures of twin boundaries in hexagonal close-packed metallic crystals with particular focus on Mg2017 / Zongrui Pei, Xie Zhang, Tilmann Hickel, Martin Friák, Stefanie Sandlöbes, et al.
-
Carbon nanomaterials as potential substitutes for scarce metals
Abstract There is growing evidence of resource problems related to the use of scarce metals in society, including the long-term risk of world-wide depletion of high-grade ores, shorter-term supply deficits and mineral related conflicts. In this...
2017 / Rickard Arvidsson, Björn A. Sandén -
Development of a multi frequency impedance measurement system for use in MEMS flow cytometers2017 / Neil J. Cole, Andrew M. Richardson, Alako Abdul-Hafiz
-
Research on image fusion of missile team based on multi-agent cooperative blackboard model
Abstract The target of cooperative engagement of missile teams is to furthest improve hit rate of target according to communication and cooperation among missiles. In this paper the problems of image fusion between missile teams in complex combat...
2012 / Guo Sen, Li Munan -
Study on the preparation of a multicomponents alloy coating with special properties
Abstract The treatment technics for substrate was researched and improved by experimentations, the technics and additive research of plating for forming ornamental and functional multicomponents alloy was carried out completely, the optimum technics ...
2011 / Li Naijun -
Influence of Solids-to-liquid and Activator Ratios on Calcined Kaolin Cement Powder
Abstract This paper summarizes the effect of activator ratio on the processing of cement powder. Geopolymer slurry was produced via alkaline activation of calcined kaolin. Once the geopolymer slurry solidified, it was crushed and ground to obtain...
2011 / Y.M. Liew, H. Kamarudin, A.M. Mustafa Al Bakri, M. Binhussain, M. Luqman, et al. -
Research on Dam Simulation System Based on OpenGL
Abstract Dam, not only has great ability to alleviate water shortages especially during the dry season which improve hydropower capacity, but also plays an imporant rule in the river ecosystem. Dam has significant effect in improving our water...
2012 / Kairong Li, Juanni Wang, Kui Zuo, Jian Yun -
Effect of magnetic particle additions on flux pinning in bulk Y-Ba-Cu-O superconductors
Abstract In order to increase the critical current density of high temperature superconductors, it is commonly employed to disperse nonsuperconducting particles as flux pinning centers into the superconductive matrix. For Y-Ba-Cu-O bulk...
2012 / T. Tsuchiya, T. Kikuchi, S. Takano, N. Koshizuka, M. Murakami -
First principles study of native defects in BeO
Abstract Using first principles calculations within the formalism of the Density Functional Theory (DFT) and the Local Spin Density Approximation (LSDA) for the exchange-correlation term, we have studied native defects (vacancies and antisites) in...
2012 / E.O. Wrasse, R.J. Baierle -
Effects of TFA addition on the growth of sintered YBa2Cu3Oy superconductors
Abstract The effects of trifluoroacetic acid (TFA) addition on the growth of a superconducting phase in sintered YBCO samples were investigated. YBCO samples with TFA addition were prepared by adding TFA (99.0%) to YBCO powder and then pressed into...
2012 / Ryusuke Kita, Keita Kuroda, Teppei Kato, O. Miura, K. Yamada, et al. -
Operation of superconducting nano-stripline detector (SSLD) mounted on cryogen-free cryostat
Abstract Recently, various types of superconducting detectors have been applied to time-of-flight mass spectrometers (TOF MS) because they can achieve 100% detection efficiency for a wide mass range from atoms to huge biomolecules. The wide mass...
2012 / Nobuyuki Zen, Koji Suzuki, Shigetomo Shiki, Masahiro Ukibe, Alessandro Casaburi, et al. -
Reproducibility and stability of C60 based organic field effect transistor
Abstract A comprehensive study concerning the reproducibility and stability of organic n-type field effect transistors is presented. C60 based OFETs were chosen to investigate the fabrication reproducibility and the long term stability because C60...
2011 / Rizwan Ahmed, Michael Sams, Clemens Simbrunner, Mujeeb Ullah, Kamila Rehman, et al. -
Annealing, Passivation and Contacting of Ion Implanted Phosphorus Emitter Solar Cells
Abstract Recently, ion implantation doping technique has shown potential to improve silicon solar cell efficiency while reducing the number of process steps. In this context, we developed and studied a p-type silicon solar cells fabrication process...
2012 / A. Lanterne, S. Gall, S. Manuel, R. Monna, D. Ramappa, et al. -
Constructing DEM Based on InSAR and the Relationship between InSAR DEM's Precision and Terrain Factors
Abstract In this paper, taking the ENVISAT satellite SAR images in Bam city as an example, the authors construct Digital Elevation Model (DEM) with InSAR technology, and by comparing the InSAR DEM with SRTM-3 DEM they also research the relationship...
2012 / Wenjun Zhang, Weihong Wang, Luwan Chen -
Discussion on the Challenges of DMFC Catalyst Loading Process for Mass Production
Abstract In manufacturing direct methanol fuel cells, there are two critical processes: manufacturing the membrane-electrode assembly, and loading the catalyst. The catalyst loading process is especially influential on the efficiency of the DMFC. In ...
2012 / Wukui Zheng, Arho Suominen, Aulis Tuominen