Materials engineering topic list of research papers
-
The New “OLD BRIDGE” Over the Danube River in Bratislava
Abstract The main task of the project was to span the river Danube towards Petrzalka with the multiple rail 1000/1435 (tram-train type) and to temporarily finish it behind the Bosakova street. The most important project section is the „new” Old...
2016 / Jan Malata, Jiri Chmelik, Lukas Bludsky, Petr Novotny -
Disruption Management for Resilient Processes in Cyber-physical Production Systems
Abstract The increasing complexity and dynamics of cyber-physical production systems (CPPS) lead to a high vulnerability to disturbances during production processes. In the event of process disruptions, decisions must be made in short time in order...
2016 / Nadia Galaske, Reiner Anderl -
Photovoltaic potential of III-nitride based tandem solar cells
Abstract In this work, we perform a detailed balance analysis of the maximum conversion efficiency of solar cells made from III-nitride materials. First, we present an analysis of single junction solar cells made from InxGa1−xN alloys, and next we...
2016 / Yassine Sayad -
Analytical Description of the Temperature Field Induced by Laser Heat Source with Any Trajectory
Abstract The paper describes a three-dimensional temporary temperature field in the semi-infinite body caused by a moving laser heat source with any trajectory. In considerations the model of the surface heat source with the Gaussian distribution of ...
2016 / Jerzy Winczek, Agata Modrzycka, Elżbieta Gawrońska -
Correlation between microstructure and wear behavior of AZX915 Mg-alloy reinforced with 12 wt% TiC particles by stir-casting process
Abstract The present work concerns with correlation between microstructure and wear behavior of AZX915 Mg-alloy reinforced with 12 wt% of TiC particles by stir-casting process. Dry sliding tests were performed under ambient environment by using a...
2016 / Nagaraj M. Chelliah, Harpreet Singh, M.K. Surappa -
Scarce Water Footprint of Energy Production in China
Abstract Water shortage and uneven distribution posed significant challenge to sustainable energy production in China. We integrated extended mix multi-regional input-output model with water scarcity to analyze consumption water footprint and...
2016 / Le Feng, Bin Chen -
Anti-reflective Coated Glass and its Impact on Bifacial Modules’ Temperature in Desert Locations
Abstract Without any doubt does anti-reflective coating (ARC) on solar glass help to boost the annual module performance in the range of 3 to 4% for monofacial modules with Sunarc AR coated glass under moderate climate conditions [1] which certainly ...
2016 / Jorge Rabanal-Arabach, Andreas Schneider -
Using Machine Vision for Flexible Automatic Assembly System
Abstract Flexible automatic assembly systems become the useful automation system for high mixed production lines of manufacturing processes. This research was aimed to design the primary prototype of the flexible automatic pick and place assembly...
2016 / Phansak Nerakae, Pichitra Uangpairoj, Kontorn Chamniprasart -
Fracture analysis of a cracked orthotropic strip bonded to a magneto-electro-elastic layer
Abstract The problem of a magneto-electro-elastic coating bonded to an orthotropic strip with multiple cracks is analyzed. The problem is solved under anti-plane shear and in-plane electric and magnetic loading. First, an analytical solution is...
2016 / M. Nourazar, M. Ayatollahi, J. Miandari, S. Varasteh -
Editorial to the Proceedings of the TensiNet - COST Action TU1303 Symposium 2016
Abstract The TensiNet Association, in collaboration with the COST Action TU1303 “Novel structural skins: Improving sustainability and efficiency through new structural textile materials and designs” and the Newcastle University organized the...
2016 / John Chilton, Peter Gosling, Marijke Mollaert, Bernd Stimpfle -
Giant Electroresistance in Edge Metal-Insulator-Metal Tunnel Junctions Induced by Ferroelectric Fringe Fields2016 / Sungchul Jung, Youngeun Jeon, Hanbyul Jin, Jung-Yong Lee, Jae-Hyeon Ko, et al.
-
A low-cost hierarchical nanostructured beta-titanium alloy with high strength2016 / Arun Devaraj, Vineet V. Joshi, Ankit Srivastava, Sandeep Manandhar, Vladimir Moxson, et al.
-
Plasticity mechanisms in HfN at elevated and room temperature2016 / Katherine Vinson, Xiao-Xiang Yu, Nicholas De Leon, Christopher R. Weinberger, Gregory B. Thompson
-
Nonlinear Elastic Wave Spectroscopy with MLS Perturbation Signal
Abstract The article describes a test procedure based on the fundamental principle of Nonlinear Elastic Wave Spectroscopy. Without integration of all test stages into one automated measurement station and without Maximum Length Sequence (MLS)...
2016 / L. Carbol, J. Martinek, I. Kusák, B. Kucharczyková -
Measurement and Analysis of Abrasive Particles Velocities in AWSJ
Abstract Abrasive water suspension (AWS) is a progressive cutting technology used in many industrial applications. Potential of this technology is very high due to good mobility and flexibility of the cutting process. It is mainly applied in the...
2016 / M. Zeleňák, J. Foldyna, M. Linde, F. Pude, T. Rentsch, et al. -
High Per formance and Flexible Supercapacitors based on Carbonized Bamboo Fibers for Wide Temperature Applications2016 / Camila Zequine, C. K. Ranaweera, Z. Wang, Sweta Singh, Prashant Tripathi, et al.
-
Facile synthesis of CoFe2O4 nanoparticles anchored on graphene sheets for enhanced performance of lithium ion battery
Abstract Recently, metal oxides as high capacity anode materials had been investigated for lithium ion batteries. However, the fast capacity fading upon cycling leaded poor durability, which hindered their application as higher energy density of...
2016 / Wen Qi, Pei Li, Ying Wu, Hong Zeng, Liting Hou, et al. -
Comparison on Electrochemical Performances of LiNi0.5Mn1.5O4 Cathode Materials Synthesized Using Different Precursors
Abstract In this work, LiNi0.5Mn1.5O4 has been synthesized by using acetate and carbonate precursors, respectively and ball-milled with citric acid, followed by heat treatment at high temperature. The structure, morphology and electrochemical...
2016 / Nabilah Mokhtar, Nurul Hayati Idris -
A Review: Simple Tools for Evaluating the Energy Performance in Early Design Stages
Abstract To make performance-based design decisions, an energy performance evaluation should be integrated into the design process. Simple tools can provide easy and rapid performance analysis without requiring detailed information as inputs. This...
2016 / Liwei Wen, Kyosuke Hiyama -
Material Modifications Caused by Thermal and Mechanical Load During Grinding
Abstract This paper discusses results acquired during surface grinding experiments performed on hardened steel workpieces. The experimental results show different zones of thermally induced material modifications during grinding depending on the...
2016 / S. Jermolajev, J. Epp, C. Heinzel, E. Brinksmeier