Materials engineering topic list of research papers
-
Starting Point, Keys and Milestones of a Computer Code for the Simulation of the Behaviour of a Nuclear Fuel Rod2011 / Armando C. Marino
-
Open-Cellular Co-Base and Ni-Base Superalloys Fabricated by Electron Beam Melting2011 / Lawrence Murr, Shujun Li, Yuxing Tian, Krista Amato, Edwin Martinez, et al.
-
Elaboration and Characterization of Mullite Refractory Products from Moroccan Andalusite2012 / Mostafa Sardy
-
Simulation of nanostructural evolution under irradiation in Fe-9%CrC alloys: An object kinetic Monte Carlo study of the effect of temperature and dose-rate
Abstract This work explores the effects of both temperature and dose-rate on the nanostructural evolution under irradiation of the Fe-9%CrC alloy, model material for high-Cr ferritic/martensitic steels. Starting from an object kinetic Monte Carlo...
2016 / M. Chiapetto, C.S. Becquart, L. Malerba -
Comparison of Optimization Techniques in a Tolerance Analysis Approach Considering Form Defects
Abstract In tolerancing analysis area, the most various existing approaches do not take form defects of parts into consideration. As high precisions assemblies cannot be analyzed with the assumption that form defects are negligible, the paper...
2016 / Lazhar Homri, Jean-Yves Dantan, Guillaume Levasseur -
Thin Wall Pipe Ultrasonic Inspection through Paint Coating
Abstract Classical ultrasonic inspection of welds is currently done for plates thicker than 8mm. The inspection of but welds in thin walled pipes has considerable implementation difficulties, due to guided waves dominating ultrasonic pulses...
2015 / Mihai Valentin Predoi, Cristian Cătălin Petre -
Implementation of a Modulated Lowpass ΔΣ-Modulator for MEMS Gyroscopes with Low-Power Consumption and Low Sampling
Abstract This paper reports on the implementation of a closed-loop readout concept for a vibratory MEMS gyroscope. The system is based on electro-mechanical (el.-mech.) ΔΣ-modulation and implemented on an integrated circuit (ASIC) with incorporation ...
2015 / S. Rombach, M. Maurer, D. Wendler, Y. Manoli -
Analytical Modelling of the Pullout Behavior of Synthetic Fibres Treated with Nano-silica
Abstract An accurate one-dimensional analytical model for simulating the pullout process of synthetic fibres from a cement matrix is proposed in the present study in order to shed light on the ductile behavior exhibited by Fibre Reinforced Concrete...
2015 / Enrico Radi, Luca Lanzoni, Andrea Sorzia -
Silk Fibroin Based Porous Materials2009 / Qiang Zhang, Shuqin Yan, Mingzhong Li
-
Cavitation Erosion Resistance Of FeAl Intermetallic Alloys And Al2O3 – Based Ceramics2015 / R. Jasionowski, Z. Pędzich, D. Zasada, W. Przetakiewicz
-
A System Dynamic Approach to Manage Changeability in Manufacturing Systems
Abstract This paper addresses the challenges in managing variety and volume in changeable manufacturing systems. A dynamic model is presented to better understand and analyse the dynamic of the strategic decisions concerning manufacturing and...
2015 / Ahmed M. Deif -
Room temperature multiferroicity in Bi4.2K0.8Fe2O9+δ2013 / Si-Ning Dong, Yi-Ping Yao, Jian-Qi Li, Yuan-Jun Song, Yu-Kuai Liu, et al.
-
Scanning frequency mixing microscopy of high-frequency transport behavior at electroactive interfaces2006 / Brian J. Rodriguez, Stephen Jesse, Vincent Meunier, Sergei V. Kalinin
-
Exploitation of Unique Properties of Zeolites in the Development of Gas Sensors2012 / Yangong Zheng, Xiaogan Li, Prabir K. Dutta
-
Optimization of Wire Electro Discharge Machining Parameters to Achieve Better MRR and Surface Finish
Abstract This paper focuses on the investigation of effect of process parameters on the responses such as MRR and surface roughness of Ti50Ni40Cu10 SMA machined by WEDM using the Taguchi techniques to obtain optimum machining process parameters. A...
2014 / M. Manjaiah, S. Narendranath, Javad Akbari -
Conditions for Bending of Thin Metal Sheet by Thermal Strain in Electrical Discharge Machining
Abstract This paper deals with the conditions for bending of sheet metals by electrical discharge machining (EDM). The thermal strain caused by the tensile stress after EDM was used to bend a sheet metal. Plate and wedged electrode were used to bend ...
2014 / Katsushi Furutani, Norimichi Yoshida -
Chemical Catalyzed Recycling of Polymers: Catalytic Conversion of PE, PP and PS into Fuels and Chemicals over H-Y
Abstract In the following study the termocatalytic degradation of polyethylene of high and low density, (HDPE, LDPE), polypropylene (PP) and polyestyrene (PS) on the H-Y zeolite was performed. The catalytic activity was carried out in a batch...
2015 / Laura C. Lerici, María S. Renzini, Liliana B. Pierella -
Comparative Design and Analysis of Mesh, Torus and Ring NoC
Abstract The research article presents the simulation and FPGA synthesis of mesh, torus and ring Network on Chip (NoC). The network is based on the Multiprocessor System on Chip (MPSoC) structure for a network cluster of 256 nodes. The paper focuses ...
2015 / Arpit Jain, Adesh Kumar, Sanjeev Sharma -
Modeling the Energy Extraction from In-stream Water by Multi Stage Blade System of Cross Flow Micro Hydro Turbine
Abstract This paper aims to present energy extraction behavior of multi stage Micro Hydro Turbine (MHT), particularly when it operates in a low velocity In-Stream water body. Development a MHT with multi stage blade (runner) for water velocity...
2015 / M.I. Shahidul, S.S Syed Tarmizi, Abdullah Yassin, Al Khalid Othman, Hushairi Zen, et al. -
Predictive study of structural, electronic, magnetic and thermodynamic properties of XFeO3 (X = Ag, Zr and Ru) multiferroic materials in cubic perovskite structure: first-principles calculations2015 / N. Moulay, M. Ameri, Y. Azaz, A. Zenati, Y. Al-Douri, et al.